interrupt 1这就相当于门牌号,因为51有5个中断源,不同的中断对应的号不一样,1对应的是定时器0中断,外部中断0 对应的是0,外部中断1对应的是2,定时器1对应的是3,串口中断对应的是4,通过不同的号区分不同的中断。至于using1这个可以不用50分享举报为您推荐 delay延时函数 at指令解析c程序 printf打印十六进制...
MODULE_DESCRIPTION("Sample GPIO and Timer Interrupt Kernel Module"); 外部IO中断验证 将驱动编译成模块,insmod加载模块后。 由于驱动检测GPIO0_D6上升沿有效,当给该引脚提供高电平时,会触发中断执行中断处理函数。 编辑 图3.1 触发IO中断
里面写的意思其实就是根据芯片手册提供的中断向量表来计算我们void xx(void)interrupt x中x的数字是多少,比如51单片机的数据手册图下图,外部中断INT0的中断向量地址为0003H,所以他的中断编号就是0,Timer0的地址为0003H+8=000BH,他的编号就是2,以此类推 然后在看一下我现在用的单片机的中断向量表,就和上面的805...
brief initialise platform before main*/__attribute__((constructor(101)))void platform_init(void){SystemCoreClockUpdate;/* Generate interrupt each 1 ms */SysTick_Config(SystemCoreClock / 1000);} __attribute__((weak))void systimer_1ms_handler(void){/* default systimer 1ms hander* you can over...
return sync.tryAcquireSharedNanos(1, unit.toNanos(timeout)); } public void unlock() { sync.releaseShared(1); } public Condition newCondition() { throw new UnsupportedOperationException(); } public String toString() { int r = sync.getReadLockCount(); ...
、下面非编码键盘程序属___ 扫描方式。 void TIMER0_ISR( void ) interrupt 1 { TR0 = 0; TH0=(65536-4096)/256; TL0=(65536-4096)%256; if( ( time % 30) == 0 ){ key = Keyscan(); } TR0 = 1; }A.程序扫描控制方式B.中断扫描控制方式C.定时扫描控制方式D.都不是的答案
1. 怎样触发执行interrupt void mainISR(void)这个中断服务函数,它是属于定时器中断还是外部中断,一旦进入interrupt void mainISR(void),它里面的中断子函数都要按顺序依次执行吗? 2. interrupt void mainISR(void)只是将所有的中断归纳在一起吗? 只要是条件合适就触发它里面的子函数吗?那如果是这样的话,interrupt...
#include "driverlib/interrupt.h" #include "driverlib/timer.h" #include "driverlib/pin_map.h" uint32_t ui32SysClkFreq; #define D2 GPIO_PIN_0 #define D1 GPIO_PIN_1 int Flag=0; float ulPeriod; char result; void Timer1AIntHandler(void){ ...
(1)//进入死循环 { keyscan(); disply(s); }}/*名称:timer0作用:定时器中断*/void timer0() interrupt 1 { TH0=(65536-50000)/256;//装入初始值 TL0=(65536-50000)%256; count++; //约50ms,count加1 if(count==20) //count加20次,即1000ms=1s,秒加一 { count=0; //count归零 s++; if...
输出结果: after 3 seconds, we will get future after 2 seconds, we will get future after 1 seconds, we will get future I from callable 方法二: 在 run 方法方法中触发一些事件(如启动一个 Timer),再在让事件监听器函数返回那些被操作大的值...