wait_on_run synth_1 #等待综合结束 launch_runs impl_1 -to_step write_bitstream #运行实现impl_1,并生成bit文件 wait_on_run impl_1 #等待实现结束 如果使用non-project模式,则脚本会复杂一些,下面提供一个模板。 注:英文注释是参考Xilinx相关文档,中文注释是为了方便阅读,由于Vivado原生不支持中文,所以为了...
wait_on_run：时间：cpu = 00:00:03;逝去了= 13:08:58。内存（MB）：峰值= 11564.246;增益= ...
set_property REFERENCE_RUN impl_1 [get_runs i_impl_IDR] launch_runs synth_1 wait_on_run synth_1 launch_runs impl_1 wait_on_run impl_1 launch_runs i_impl_IDR ERROR: [Common 17-69] Command failed: Run 'i_impl_IDR' is not active What is wrong here? Thank you, best regards. Exp...
wait_on_run Ensures the run is complete before processing the next commands in a Tcl script. open_run Opens either the synthesized design or implemented design for reporting and analysis. A design must be opened before information can be queried using Tcl for reports, analysis, and so forth....
wait_on_runs impl_1 ... The reset_run command fails if I delete the impl_1 run in the Vivado Design Runs view. Is there any command to determine the existence of the specific run before proceeding? Solution Please find example code to do this below: start_...
[get_runs impl_1] set_property STEPS.PHYS_OPT_DESIGN.TCL.POST [pwd]/post_phys_opt_design.tcl [get_runs impl_1] set_property STEPS.ROUTE_DESIGN.TCL.POST [pwd]/post_route_design.tcl [get_runs impl_1] launch_runs impl_1 -to_step write_bitstream wait_on_run impl_1 puts "...
wait_on_run impl_1 # # Generate a timing and power reports and write to disk # comment out the open_run for batch mode open_run impl_1 report_timing_summary -delay_type min_max -report_unconstrained \ -check_timing_verbose -max_paths 10 -input_pins -file imp_timing.rpt ...
wait_on_run impl_1 #打开硬件管理器 open_hw 我知道还不够详细,但是方法大概就是如此,你可以运行一步操作,之后打开这个文件,看看运行了什么样的Tcl命令,这样便明白了每条Tcl命令的含义。 在工程模式下如果学会了使用Tcl命令,不仅可以装逼(更装逼的是非工程模式下的Tcl命令),还可以更方便的去使用Vivado IDE,当然...
[get_runs impl_1] set_property STEPS.PHYS_OPT_DESIGN.TCL.POST [pwd]/ post_phys_opt_design.tcl [get_runs impl_1] set_property STEPS.ROUTE_DESIGN.TCL.POST [pwd]/ post_route_design.tcl [get_runs impl_1] launch_runs impl_1 -to_step write_bitstream wait_on_run impl_1 puts "...
- run: echo 'done'The TCL script "synth-impl-bit.tcl" called above that contains the hanging command is:source generate_project_basys3.tcl cd /home/vivado/project/project_basys3 set_param general.maxThreads 1 launch_runs synth_1 -verbose wait_on_run synth_1 -verbose launch_runs...