时序分析中,Report_timing_summary默认是对所有路径进行分析,当工程设计较大时,时序路径较多,想要查找指定时序路径的时序情况就不方便,此时就可以使用“Report Timing"功能,但“ReportTiming”不会报告“Pulse Width”(脉冲宽度)。 二、配置选项概览图 下图是Report Timing 中所有配置选项的结构图。 三、配置选项详解 ...
report_timing_summary 我们先看看 report_timing_summary,实际上,不仅在布局布线后,在综合后甚至是更具体的实现过程中 的每一小步之后都可以运行,从而得到一个全局的时序报告。 在Vivado IDE 中点击 Report Timing Summary 后可以改变报告的内容,例如每个时钟域报告的路径条数,是否 setup 和 hold 全都报告等等。每...
Vivado运行完Implementation后,Design Runs都会有如下的提示: 当然Timing Summary中也会有: 从上面的Design Timing Summary中可以看出,WNS以及TNS是针对Setup Time Check的,而WHS以及TNS是针对Hold Time Check的, Design Timing Summary对应的Tcl命令为:report_timing_summary. WNS以及TNS,WHS以及THS是我们需要着重关注的...
在进行时序分析时,除了slack的分析,还存在pulse width的检查,下面将对pulse width检查进行详细说明。在report timing summary报告中,也会带上Pulse Width检查结果。 二、Report pulse width 2.1 Report pulse width 脉冲宽度检查是对信号波形进行一些规则检查,如检查设计是否满足每个时序单元时钟管脚的最小周期、最大周期...
在Vivado的Flow Navigator中,选择“Reports” > “Timing” > “Report Timing Summary”。在弹出的对话框中,你可以根据需要配置报告选项,然后点击“OK”生成报告。查找特定路径: 在生成的时序报告中,你可以通过路径名称、起点、终点或其他关键信息来查找特定的路径。 Vivado的时序报告通常会列出多条路径,你可以通过...
通过菜单栏的Reports->Timing->Report Exceptions可以进入到报告的配置界面 配置界面主要有Targets和Options两部分组成 Results Name:设置Exceptions报告的名称 Start Points:指定生成Exceptions报告的时序路径起点,类型可为Cells,Clocks,Cell Pins,I/O Port四种
在时序报告中,可以针对两类特殊的约束专门进行报告,一类是前面介绍过的Report Exception,包含了约束set_multicycle_path/set_false_path/set_max_dealy/set_min_delay。另一类就是本文要介绍的set_bus_skew约束,对应的分析为Report Bus Skew,该报告不包含在Report Timing Summary中。
Why does "set_max_delay -datapath_only" appear in the Unconstrained Path section of the "report_timing_summary" report? I used a set_max_delay constraint in my design, but now I see the TS_WR_CLK to TS_RD_CLK analysis under the "Unconstrained Paths" section of the ...
report_timing_summary -cell [get_cells U1] -name test_1 -max_paths 100 -delay_type min_max Note:paths whose startpoint or endpoint belong to the cell hierarchy are reported. To report the interface timing of the hierarchical cell, you can use the following command: ...
report_timing_summary -cell [get_cells U1] -name test_1 -max_paths 100 -delay_type min_max Note:paths whose startpoint or endpoint belong to the cell hierarchy are reported. To report the interface timing of the hierarchical cell, you can use the following command: ...