+pulse_r / <数字>:拒绝宽度于模块路径延迟数百分的任何脉冲。+putprotect + <标录> :指定受保护件的标录。Q-q:禁VCS编译器消息。R-R:VCS将可执件链接在起后,即运可执件。您可以将任何运时选项添加到vcs命令。+race: 指定VCS在仿真过程中成设计中所有竞争状况的报告,并将此报告写race.out件中。+race...
在SDF格式中可以指定固有延迟(intrinsic delays),互连延迟(interconnect delays),端口延迟(port delays),时序检查(timing checks),时序约束(timing constraints)和路径脉冲(PATHPULSE)。 使用VCS读取SDF文件时,会将延迟值“反向标注(back-annotates)”到设计中,即在源文件中添加或者更改延迟值。
在SDF格式中可以指定固有延迟(intrinsic delays),互连延迟(interconnectdelays),端口延迟(port delays),时序检查(timing checks),时序约束(timing constraints)和路径脉冲(PATHPULSE)。 使用VCS读取SDF文件时,会将延迟值“反向标注(back-annotates)”到设计中,即在源文件中添加或者更改延迟值。 可以使用$sdf_annotate系统...
pulse _ e/num 1 pulse _ r/num 2 pulse _ int _ e/num 1 pulse _ int _ r/num 2窄脉冲的后沿所调度的时间会抵消起始沿所调度的时间。如果sdf反向标准网络不使用原始、连续分配和MIPD惯性延迟模型,则应添加多源int延迟选项,否则应使用MIPD惯性延迟模型。对于惯性延迟,num1=0和num2=0并不意味着传输...
在SDF格式中可以指定固有延迟(intrinsic delays),互连延迟(interconnect delays),端口延迟(port delays),时序检查(timing checks),时序约束(timing constraints)和路径脉冲(PATHPULSE)。 使用VCS读取SDF文件时,会将延迟值“反向标注(back-annotates)”到设计中,即在源文件中添加或者更改延迟值。
VCS简明使用教程
VCS简明使用教程
+pulse_r option but only applies to interconnect delays. +pulse_onevent Specifies that when VCS encounters a pulse shorter than the module path delay, VCS waits until the module path delay elapses and then drives an X value on the module output port and displays an error message. +pulse...
+transport_path_delays +pulse_e/num1 +pulse_r/num2 +transport_int_delays +pulse_int_e/num1 +pulse_int_r/num2 上述两个选项开启了传输延迟模式,后面的两个选项是必须的;num1和num2都是延 时的百分比,小于num2的脉冲会被过滤掉(filter out ),大于num2但小于 num1的脉冲会被x值代替。如果想实现...
+transport_path_delays +pulse_e/num1 +pulse_r/num2 +transport_int_delays +pulse_int_e/num1 +pulse_int_r/num2 上述两个选项开启了传输延迟模式,后面的两个选项是必须的;num1和num2都是延 时的百分比,小于num2的脉冲会被过滤掉(filter out),大于num2但小于 num1的脉冲会被x值代替。如果想实现...