// Set FLL Div = fDCOCLK/2 __bic_SR_register(SCG0); // Enable the FLL control loop // Worst-case settling time for the DCO when the DCO range bits have been // changed is n x 32 x 32 x f_MCLK / f_FLL_reference. See UCS chapter in 5xx // UG for op...
3. 在做new part时总出现下⾯地问题，如何解决?Warning: A pin with the name “GND”ist duplicated on the part!!E Part⾥⾯的GND重复了，你把GND管脚都改成Power类型的就可以了,或者说选择带有POWER 类型的库 3. Occurrences和Instances有什么区别 Occurrences和Instances有什么区别,⽤在什么情况下.简...
Y6 e5 K) I [DRC0003] Port has a type which is inconsistent with other ports on the net TM CL--〉Net TMCL 两端的端口类型冲突,修改一下 type 就好了 [DRC0004] Possible pin type conflict U13,Y Output Connected to Bidirectional P ort--〉经常会有的错误,修改 pin % H D c$ _ \8 h0...
Output Pins Voltage -0.3 to 25 V VI Logic Input Voltage (SDA, SCL, DSQIN, ISEL) -0.3 to 7 V VDETIN Detector Input Signal Amplitude -0.3 to 2 VPP VOH IGATE t(s)VSENSE VADDRESS ucTstg dTop Logic High Output Voltage (DSQOUT) Gate Current Current Sense Voltage Address Pin Voltage ...
This code will measure the 1.1 VDC Bandgap reference against AVCC and report the approximate value to the Serial Monitor. unsigned vcc; void setup() { // initialize digital pin LED_BUILTIN as an output. pinMode(LED_BUILTIN, OUTPUT); ...
Chip Select (CS) When CS is HIGH, the device is deselected and the SO output pin is at high impedance and unless a nonvolatile write cycle is underway, the device will be in the standby power mode. CS LOW enables the device, placing it in the active power mode. It should be noted ...
70-ns typical response from current-sense to gate drive output 1.5% tolerance voltage reference Same pinout as UC3842 and UC3842A UCC2803-Q1的参数(英文): Topology Boost, Flyback, Forward Duty cycle (Max) (%) 100 Supply voltage (Max) (V) 12 UVLO thresholds on/off (V) 4.1/3.6 Features...
voltage VI Input voltage (OE output enable pin, VL power supply referred) VI/OVL VI/OVCC Top dt/dv I/OVL voltage I/OVCC voltage Operating temperature Input rise and fall time (OE control pin)(1) dt/dv Input rise and fall time(...
2、有些IC既有VDD引脚又有VCC引脚,说明这种器件自身带有电压转换功能。 3、在场效应管(或COMS器件)中,VDD为漏极,VSS为源极,VDD和VSS指的是元件 引脚,而不表示供电电压。 GND:公共地 DGND:数字地 AGND:模拟地 SGND:信号地 1.OrCAD中拖动元件时如何不连线一起拖动?
I-V IN converter &Input bias Pre Amp AGC Amp Limit Amp control Comparator VCC Voltage Reference Circuit Integrator &wave shaping Output Stage OUT Fset Bias Circuit Frequency setting Frequency Trimming Absolute Maximum Ratings (Ta=25℃) Parameter Symbol MIN. Supply Voltage VCC 0 Output Voltage...