`uvm_do_with(tx , { tx.addr == local::addr; tx.data == local::data; } 工作正常。 另一个解决方案正在命名我的local变量除了以外的东西addr和data. 扩张的uvm_do_with宏说,它呼叫item.randomize(),所以我假设在这种情况下,电话会 item.randomize(addr,data) with {addr == local::addr; data==...
randomize(item); finish_item(item); endtask virtual task body(); repeat (num_trans) do_rw($urandom(),$urandom()); endtask ... endclass : simple_seq_do_with 原文标题:UVM中的uvm_do宏 文章出处:【微信号:芯片验证工程师,微信公众号:芯片验证工程师】欢迎添加关注!文章转载请注明出处。
位start_item做准备。 下面回到`uvm_do_on_pri_with中。 SEQ_OR_ITEM被返回后,后面要先判断SEQ_OR_ITEM是SEQ还是ITEM,从而为执行不同的动作。 如果是ITEM,则start_item(SEQ_OR_ITEM, PRIORITY) , randomize, finish_item(SEQ_OR_ITEM, PRIORITY)。 如果是SEQ,则调用start(SEQR,this,PRIORITY, 0)。 后面...
下面回到`uvm_do_on_pri_with中。 SEQ_OR_ITEM被返回后,后面要先判断SEQ_OR_ITEM是SEQ还是ITEM,从而为执行不同的动作。 如果是ITEM,则start_item(SEQ_OR_ITEM, PRIORITY) , randomize, finish_item(SEQ_OR_ITEM, PRIORITY)。 如果是SEQ,则调用start(SEQR,this,PRIORITY, 0)。 后面分两次分析start方法,以...
req.randomize(); if(status_type) begin //Using the value set by top level test or sequence //instead of the random value. req.type = local_type; end if(status_device_id) begin //Using the value set by top level test or sequence ...
17 req.randomize with {data == 10;}; 18 `uvm_info("SEQ", $sformatf("sent a item \n %s",req.sprint()), UVM_LOW) 19 finish_item(req); 20 get_response(tmp); 21 void'($cast(rsp, tmp)); 22 `uvm_info("SEQ", $sformatf("got a item \n %s",rsp.sprint()), UVM_LOW) ...
然后选择对应的item,选择前做randomize 39行req.clone()返回的是句柄是uvm_object,为此需要转换 finish_item等到item_done的时候再release 当seq挂载到sqr上是,自身的body()将自动执行,挂载并不意味这随机化seq 上例没有指明driver拿到的类型,REQ的类型为默认的uvm_sequence_item ...
一个宏封装了产生item的四个步骤,相当于把所有的事情做完了,极大的方便了使用。除了uvm_do宏之外,uvm_do系列宏中另外一个经常使用的就是uvm_do_with。它的使用方式如下: 使用uvm_do_with宏之后,那么产生transaction的第三部中的assert(tr.randomize() with {tr.crc_err == 1};如果需要发送多个包(其中pkt_...
item.randomize() //随机化 this.mid_do(item) sequencer.send_request(item) sequencer.wait_for_item_done() this_post_do(item) 总结就是1创建实例 2随机化 3随机化后实例发送给sequencer seq sequencer driver关系 uvm do 宏包括: uvm_do_on_pri_with(seq or item,sequencer,prior,constraint); ...
`uvm_do_on_with(axi_rd_seq_0_1, p_sequencer.axi_read_seqr_0_1, {axi_rd_seq_0_1.burst_num ==`d100; axi_rd_seq_0_1.row_addr_sel == 2'b01; axi_rd_seq_0_1.master_arid == 2'b01;}) you could write: axi_rd_seq_0_1.randomize() with {axi_rd_seq_0_1.burst_num ...