the xHC to pre-fetch the next TRB of a TD */snps,xhci-trb-ent-quirk;/* when set, need warm reset on resume */snps,usb3-warm-reset-on-resume-quirk;status="disabled";};};&usbdrd3_0{status="okay";extcon=<&fusb0>;};&i2c4{status="okay";i2c-scl-rising-time-ns=<160>;i2c-s...
5.2.8 Set Configuration(设定配置)请求 86 5.2.9 Get Interface(获得接口)请求 86 5.2.10 Set Interface(设置接口)请求 87 5.2.11 Synch Frame(帧同步)请求 87 5.2.12 Set SEL(设定选择)请求 87 5.2.13 Set Isochronous Delay(设定等时延时)请求 88 5.3 其他请求 88 5.3.1 类...
当USB_SEL2置为高时,则4,6脚和3,7脚直通,输出为OTG信号。这里因为需要芯片一直处于工作状态,所以将OE#接地。差分信号与SGM7222的正负引脚要对应。V+为芯片的电源引脚,要外接去耦电容。 4. SGM7222实物图 SGM7222的PCB设计图如下所示。总共用了2颗SGM7222。 图4 SGM7222 PCB图 左边器件为USB HUB芯片,右边...
DeviceHwVerifierSetSelFailureUSB 3.0 设备未能完成 SET_SEL 请求。 此设备会将该请求信息用于链接电源管理 (LPM)。 此设备可能无法完成该请求,因为驱动程序不需要请求信息或出现暂时性错误。 但是,驱动程序无法区分这些原因。 报表中未捕获此错误。 DeviceHwVerifierSerialNumberMismatchOnRenumeration此设备在重新枚...
(7 downto 0); -- 8 位输出数据总线,仅用于输出sel_in_n : in STD_LOGIC; -- 总线输入控制信号sel_out_n : in STD_LOGIC -- 总线输出控制信号);end IOSwitch;architecture IOSwitch of IOSwitch is-- 创建一个内部信号,用作数据传递signal data_tmp : STD_LOGIC_VECTOR(7 downto 0);begin-- ...
集线器深度值被软件使用设置集线器深度(Set Hub Depth)请求来分配。集线器进入被配置状态之前,会忽略路由字串(Route String),而假设所有的包是直接路由到该集线器自己。集线器上行端口将被端口号0来代表,而下行端口由1号端口开始,并循序地向上计数。每当一个集线器控制器以包含路由字串(Route String)的包回应一个路由...
The host sends a Set Isochronous Delay request to inform the device of the bus delay for isochronous packets. The host sends a Set SEL request to inform the device of the system exit latency (the amount of time required to transition out of a low-power state). ...
The USB set SEL request failed. A request for the USB BOS descriptor failed. A request for the USB device qualifier descriptor failed. A request for the USB serial number string descriptor failed. A request for the USB language ID string descriptor failed. ...
#define GPIO_INPUT_PIN_SEL ((1ULL << GPIO_INPUT_IO_0) | (1ULL << GPIO_INPUT_IO_1)) //混合 #define ESP_INTR_FLAG_DEFAULT 0 //中断标志清零 // 设置消息队列,用于传递中断的信息返回变量 static xQueueHandle gpio_evt_queue = NULL; //将空变量gpio_evt_queue定义为队列(xQueueHandle) ...
if(mode_set_hs) mode_hs <= 1'b1; always @(posedge clk) if(suspend_clr) USB_suspend <= 1'b0; else if(suspend_set) USB_suspend <= 1'b1; always @(posedge clk) if(attached_clr) USB_attached <= 1'b0; else if(attached_set) USB_attached <= 1'b1; ...