ufo 可以看到这样一个握手。上面的解释是 “High speed Detection Handshake High speed Detection Handshake state detected Status The handshake completed successfully.When does this state occur?All high speed devices start at full speed to ensure USB 1.1 backward compatibility. If the upstream port ...
All high speed devices start at full speed to ensure USB 1.1 backward compatibility. If the upstream port (device) supports high speed signaling, it will generate a Chirp K state on the bus after Reset. If the downstream port (host) also supports high speed signaling, it will generate Chirp...
USB 2.0 Hi-Speed 4-Port Hub Controller Datasheet Chapter 2 Acronyms and Definitions 2.1 2.2 Acronyms EOP: End of Packet EP: Endpoint FS: Full-Speed GPIO: General Purpose I/O (that is input/output to/from the device) HS: Hi-Speed HSOS: High Speed Over Sampling I2C®: Inter-Integrated...
USB3.0使用的是Synopsys公司的IP,驱动也使用Synopsys的dwc3 USB驱动。 2.USB3.0 OTG Controller简介 USB3.0 OTG控制器可以作为主机(Host)、设备(Device),或者根据从USB2.0 PHY和DFP/UFP/Data Role Swap输入的ID状态确定是USB2.0/3.0 OTG A设备和B设备。可以以Super-Speed/High-Speed/Full-Speed/Low-Speed的速度...
我们知道USB2.0向下兼容USB1.x,即高速2.0的hub能支持所有的速度类型的设备,而USB1.x的hub不能支持高速设备(High Speed Device)。因此,如果高速设备挂到USB1.x的hub上,那该设备只能工作在全速模式下。不管是hub还是设备(device),对于速度的区分是非常重要的,否则,后续的通信根本无法进行。
hub通过检测USB总线空闲时的差分线的高低电压来判断所连接设备的速度类型,当host发来Get_Port_Status请求时,hub就可以将此设备的速度类型信息回复给host。USB 2.0规范要求速度检测要先于复位(Reset)操作。 根据是D+还是D-被拉高来判断到底是什么设备(全速/低速)插入端口。
compliant portable device is detected on the downstream port. And, after the handshake has been completed, MA8608 allows portable devices to draw up to 900mA (High speed); 1.5A (Low/Full speed) from charging downstream ports (CDP) or 1.5A from dedicated charging port (DCP). The MA8608 ...
速度 High Speed 数据速率 480 Mb/s 最小工作温度 0 C 最大工作温度 + 70 C 接口类型 I2C, SMBus, SPI, USB 端口数量 4 Port 湿度敏感性 Yes 工作电源电压 3.3 V 单位重量 410 mg 可售卖地 全国 型号 USB4604-1080HN 深圳市西昂特科技有限公司成立于2007年,以经营欧、美集成电路为...
Super Speed 5gbpsHubUSB3.07PortMulti Splitter With LED 广州市创以晨电子科技有限公司14年 回头率:23.5% 广东 广州市天河区 ¥23.00 7PortAluminum MultiUSB3.0 SplitterUSB2.0HUBHigh Speed 广州市创以晨电子科技有限公司14年 回头率:14.1% 广东 广州市天河区 ...
1、Isochronous (High-Speed) Transfer Descriptor (iTD) 2、Queue Head 2.1、Queue Element Transfer Descriptor (qTD) 5.1.3 Asynchronous Schedule Asynchronous Schedule 内部实现非常的简单就只有一级链表,链表中只有Queue Head类型的描述符。每个时间片内传输完 Period 数据以后,再尽可能的传输 Asynchronous 数据即可...