If you run into the following error, here are the exact steps you can use: detection.node was compiled against a different Node.js version using NODE_MODULE_VERSION 72. This version of Node.js requires NODE_MODULE_VERSION 80. Please try re-compiling or re-installing ...
3. 在 Hard Reset 产生后,寄望于对端可以在 tNoResponse 的时间内对 Hard Reset 请求做出响应。如果未有响应,进行 Hard Reset 累加(最大为 2)直到 SRC 进入 Error Recovery 状态。 2.6.2 SNK Operation 在连接状态时(没有 PD 的连接) 1. SNK 会通过对端有无输出 vSafe5V 来判断连接。 2. 对 DRP 端口...
首先修改~/catkin_ws/src/apriltag_ros/apriltag_ros/launch/continuous_detection.launch文件。 apriltag_ros 需要订阅相机图像数据与相机信息,比如对于USB摄像头,在开启相机时会发布两个相关的 topic: /usb_cam/camera_info /usb_cam/image_raw 因此需将camera_name与camera_frame的内容修改...
• 从Polling.Active, Polling.Configuration, Recovery.Active, or Recovery.Configuration字状态中任何之一超时都将导致训练序列错误(Training Sequence error)。
很正常，是bios出现轻微错误，一般长期不开的电脑或者电流冲击，会出现这种问题。也可能是电池坏了没有电了，按下f1就能继续正常使用了，如果按f2，可以进入bios里面，无需任何设置。选择存盘，然后退出，以后就正常了。检查
52、pondHC(Do_halt);ErrorCount < 3 RespondHC(Do_same_cmd);Packet_ready(HSU2)(HSU2.PID /= STALL and HSU2.PID /= NAK and HSU2.PID /= ACK) orHSU2.timeout实战电子:点击打开,有问必答)(勿扰100%拒绝水贴,10名疯狂工程师运营的Change: p. 223, figure 8-32: caption should be “FS Bu...
三、在Jetson AGX Orin上尝试maskDetection同时打开三个摄像头 再试试口罩识别(原来用两个1080p的摄像头没问题,参见张小白:张小白教你在Jetson AGX Orin上使用USB摄像头进行口罩识别) 具体方法是: cd /home1/zhanghui/maskDetection_jetson cp 2_demoMask.sh 2_demoMask_2.sh ...
Control transfers support error detection and retry. Interrupt—used to support small, limited-latency transfers to or from a device such as coordinates from a pointing device or status changes from a modem. Interrupt transfers support error detection and retry. Isochronous—used for periodic, ...
- Bus collision detection and arbitration - Integrated signal conditioning - Slave address masking - IPMI support - SMBus support Communication Modules (Continued): • UART (up to four modules): - Interrupt on address bit detect - Interrupt on UART error ...
{ USBD_StatusTypeDef usb_status = USBD_OK; switch (hal_status) { case HAL_OK : usb_status = USBD_OK; break; case HAL_ERROR : usb_status = USBD_FAIL; break; case HAL_BUSY : usb_status = USBD_BUSY; break; case HAL_TIMEOUT : usb_status = USBD_FAIL; break; def...