.name = "cfi_flash", .id = UCLASS_MTD, .of_match = cfi_flash_ids, .probe = cfi_flash_probe, }; In the kernel, we have “cfi-flash” string only in file drivers/mtd/maps/physmap_of_core.c. To compile this driver I have enabled below configurations: # # RAM/ROM/Flash chip...
ft5x0x_ts_probe FTS I2C TEST Success!ret:1 input: Capacitance_ts as /devices/virtual/input/input1 [FT5X06_TP]:the FW_VER = 6 [FTS] Firmware version = 0x6 ft5x0x:ft5x0x_ts_probe() - sysfs_create_group() succeeded. ==probe over = rtc-pcf8563 1-0051: c...
mma8451 1-001c: read chip ID 0x1 is not equal to 0x1a or 0x2a! mma8451: probe of 1-001c failed with error -22 imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) cpuidle: using governor ladder cpuidle: using governor menu sdhci...
[ 0.066223] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.066436] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.066619] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.067169] omap_mux_in...
Stlink commandline tool name: st-info and st-util Target chip (and board if applicable): STM32F100RBT6 Futher we kindly ask you to describe the detected problem as detailed as possible and to add debug output if available, by using the following template: ...
[ 0.047036] …TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.066212] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2b24ac223d3, max_idle_ns: 440795261031 ns [ 0.066215] Calibrating delay loop (skipped), value calculated using timer frequency… 5986.12 BogoMI...
.name = "cfi_flash", .id = UCLASS_MTD, .of_match = cfi_flash_ids, .probe = cfi_flash_probe, }; In the kernel, we have “cfi-flash” string only in file drivers/mtd/maps/physmap_of_core.c. To compile this driver I have enabled below configurations: # # RAM/ROM/Flash c...
mma8451 1-001c: read chip ID 0x1 is not equal to 0x1a or 0x2a! mma8451: probe of 1-001c failed with error -22 imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) cpuidle: using governor ladder cpuidle: using governor menu sdhci:...
imx6q-pinctrl 20e0000.iomuxc: could not request pin 139 on device 20e0000.iomuxc imx-i2c 21a8000.i2c: Error applying setting, reverse things back imx-i2c 21a8000.i2c: can't get/select pinctrl imx-i2c: probe of 21a8000.i2c failed with error -22 media: Linux media...
mma8451 1-001c: read chip ID 0x1 is not equal to 0x1a or 0x2a! mma8451: probe of 1-001c failed with error -22 imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) cpuidle: using governor ladder cpuidle: using governor menu sdhci...