--开发模式: 开机后立刻按下 空格键, 会进入 uboot 的命令行模式, 即开发模式; 2. 使用 Source Insight 阅读 uboot 源码 Source Insight 使用流程: --创建工程: "菜单栏" --> "Project" --> New Project 弹出下面的对话框, 在对话框中输入代码的保存路径 和 工程名; --每个工程有自己的文件: 点击 ...
(1)uboot的终极目标就是启动内核,启动内核在uboot中表现为一个指令,uboot命令行中调用这个指令就会启动内核(不管成功与否,所以这个指令是一条死路)。 (2)差别:bootm启动内核同时给内核传参,而Go命令启动内核不传参。bootm其实才是正宗的启动内核的命令,一般情况下都用这个;go命令本来不是专为启动内核设计的,go...
#endif #if defined(CONFIG_ARM) || defined(CONFIG_NDS32) || defined(CONFIG_RISCV) || \ defined(CONFIG_SANDBOX) board_init, //板子初始化 #endif #ifdef CONFIG_CLOCKS set_cpu_clk_info, /* Setup clock information */ #endif #ifdef CONFIG_EFI_LOADER efi_memory_init,//efi 内存初始化 #en...
4 * The Mask ROM will have already initialized 5 * basic memory. Go here to bump up clock rate and handle 6 * wake up conditions. 7 */ 8 b lowlevel_init @ go setup pll,mux,memory 9 ENDPROC(cpu_init_crit) 接下来会跳转到lowlevel_init去执行,所做工作即注释所提及的,初始化PLL\MUX\...
│ ├── openrisc │ ├── powerpc │ ├── sandbox │ ├── sh │ ├── sparc │ └── x86 看得出来uboot支持的硬件体系是很全面的。 3、board目录是目前已适配的板子: ├── board │ ├── a3000 │ ├── a4m072
最早,DENX软件工程中心的Wolfgang Denk基于8xxrom的源码创建了ppcboot工程,并且不断添加处理器的支持。后来,Sysgo Gmbh把ppcboot移植到ARM平台上,创建了ARMboot工程。然后以ppcboot工程和armboot工程为基础,创建了u-boot工程。 现在u-boot已经能够支持PowerPC、ARM、X86、MIPS体系结构的上百种开发板,已经成为功能最多...
opensbi下的riscv64裸机系列编程1(串口输出) opensbi下的riscv64裸机系列编程1(串口输出) 1.说明 2.opensbi的编译 3.基本环境的准备 3.1 准备qemu 3.2 准备交叉编译工具链 4.工程完善 5.封装的sbi 2020-12-31 10:56:28 技巧|多串口输出打印 串口输出是单片机基本的外设使用,也是必须基本的一项基本技能,为了使...
- CONFIG_SKIP_LOWLEVEL_INIT [ARM, NDS32, MIPS, RISC-V only] If this variable is defined, then certain low level initializations (like setting up the memory controller) are omitted and/or U-Boot does not relocate itself into RAM. Normally this variable MUST NOT be defined. The only ...
- CONFIG_SKIP_LOWLEVEL_INIT [ARM, NDS32, MIPS, RISC-V only] If this variable is defined, then certain low level initializations (like setting up the memory controller) are omitted and/or U-Boot does not relocate itself into RAM. Normally this variable MUST NOT be defined. The only ...
openrisc Files generic to OpenRISC architecture /cpu CPU specific files /lib Architecture specific library files /powerpc Files generic to PowerPC architecture /cpu CPU specific files /mpc5xx Files specific to Freescale MPC5xx CPUs /mpc5xxx Files specific to Freescale MPC5xxx CPUs /mpc8xx Files...