使用C6748的UART1作为收发串口,输入的ttl电平信号通过ttl转485电平转换电路转为485信号,再送到485通信设备,ttl转485电平转换电路如图: 主函数如下: AI检测代码解析 int main(void) { // 外设使能配置 PSCInit(); // GPIO 管脚复用配置 GPIOBankPinMuxSet(); // UART 初始化 UARTInit(); // 发送字符串 /...
uart_read_bytes 函数阻塞的可能原因包括: 串口缓冲区为空:如果 UART 设备的接收缓冲区中没有数据可读,read 操作将会阻塞,直到有数据可读或者发生错误。 串口配置问题:如果串口参数(如波特率、数据位、停止位、校验位等)配置不正确,可能导致数据传输异常,从而影响数据读取。 外部设备故障:如果连接的外部设备出现故障...
51CTO博客已为您找到关于uart_read_bytes函数的相关内容,包含IT学习相关文档代码介绍、相关教程视频课程,以及uart_read_bytes函数问答内容。更多uart_read_bytes函数相关解答可以来51CTO博客参与分享和学习,帮助广大IT技术人实现成长和进步。
在使用int uart_read_bytes(uart_port_tuart_num, uint8_t *buf, uint32_t length, TickType_t ticks_to_wait)这个函数时遇到些问题,请问,参数里面ticks_to_wait是表示串口等待这么长时间读一次?如果将这个参数改成portMaxDelay,是不是就一直是被挂起状态?参数里面length是给定的值,还是ticks_to_wait时间内...
I set ticks_to_wait to zero, because this data should be in the UART ringbuffer. I would expect that the uart_read_bytes() to return all the characters up until the UART_PATTERN_DET event was triggered.How do I get all the characters in the UART buffer after the UART_PATTERN_DET ...
uart_read_bytes 一、试验概述 (1)试验目的:掌握通过文件系统操作UART设备的方法. (2)在linux中,所有设备都是以文件的形式被打开并进行读/写操作的,本试验中使用POSIX兼容的文件操作接口函数对底层设备进行操作.其中,POSIX是Portable Operating System Interface for UNIX的首字母缩写,是一套IEEE和ISO标准....
51CTO博客已为您找到关于uart_read_bytes的相关内容,包含IT学习相关文档代码介绍、相关教程视频课程,以及uart_read_bytes问答内容。更多uart_read_bytes相关解答可以来51CTO博客参与分享和学习,帮助广大IT技术人实现成长和进步。
在使用int uart_read_bytes(uart_port_tuart_num, uint8_t *buf, uint32_t length, TickType_t ticks_to_wait)这个函数时遇到些问题,请问,参数里面ticks_to_wait是表示串口等待这么长时间读一次?如果将这个参数改成portMaxDelay,是不是就一直是被挂起状态?参数里面length是给定的值,还是ticks_to_wait时间内...
UART READ BYTES ERROR (IDFGH-1839)#4048 Closed What if you change this You should then get data event and break event As for the mod, the newer uart.c has changed so much I can't figure out where to put the mod now... uart.c at line 850 now is: ...
It seems that when calling uart_read_bytes() the hardware FIFO buffer is not flushed, see this thread. This causes problems when you need to quickly react to events, such as the UART_PATTERN_DET event. It causes the following issue: I ha...