硬件流控制通过在UART/USART通信接口上引入额外的控制信号(RTS/CTS)来实现数据传输的流量控制和错误检测。 ```c // 配置USART的硬件流控制 void configureHardwareFlowControl(USART_HandleTypeDef *husart) { husart->Init.HwFlowCtl = UART_HWCONTROL_RTS_CTS; // 启用RTS/CTS流控制 HAL_UART_Init(husart);...
- Hardware flow control enabled (RTS and CTS signals)- Receive and transmit enabled @par Directory...
RTS(请求发送):RTS线(Request to Send)通常用于流量控制,发送器通过RTS线向接收器请求发送数据,以确保接收端准备好接收数据。 CTS(清除发送):CTS线(Clear to Send)通常用于流量控制,接收器通过CTS线向发送器发送信号,告知发送器可以发送数据。 其中TX、RX、GND三根线是UART通信必须的,用于实现数据的双向传输和提供...
< UART stop bits*/ // 硬件流控模式 uart_hw_flowcontrol_t flow_ctrl; /*!< UART HW flow control mode (cts/rts)*/ uint8_t rx_flow_ctrl_thresh; /*!< UART HW RTS threshold*/ union { // 时钟源 uart_sclk_t source_clk; /*!< UART source clock selection...
.flow_ctrl = UART_HW_FLOWCTRL_CTS_RTS, .rx_flow_ctrl_thresh = 122, }; // 配置UART参数 ESP_ERROR_CHECK(uart_param_config(uart_num, &uart_config)); 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 多步配置 通过调用下面表格中的专用函数来单独配置特定参数。如果重新配置单个参数,这些函数...
代码并不复杂,我使用cubeMX来初始化配置了usart2的代码库,并使用两个基于cmsis v2 api的线程定期接收和传输(2秒)。_8B; huart2.Init.Parity =UART_PARITY_NONE; huart2.Init.HwFlowCtl =UART_HWCONTROL_RTS; huart 浏览14提问于2020-02-12得票数 2 ...
PIN_FUNC_SELECT(PERIPHS_IO_MUX_MTDO_U, FUNC_U0RTS); //HW FLOW CONTROL RTS PIN #endif #...
typedefstruct{intbaud_rate;//波特率uart_word_length_tdata_bits;//数据位uart_parity_tparity;//奇偶校验位uart_stop_bits_tstop_bits;//停止位uart_hw_flowcontrol_tflow_ctrl;//硬件流控uint8_trx_flow_ctrl_thresh;//硬件流控的RTS阈值union{uart_sclk_tsource_clk;//时钟源booluse_ref_tick __attri...
.flow_ctrl = UART_HW_FLOWCTRL_CTS_RTS, .rx_flow_ctrl_thress = 122, }; // Configure UART parameters ESP_ERROR_CHECK(uart_param_config(uart_num, &uart_config)); 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 以上所有函数有一个_get_等价方法用来获取当前设置。比如 uart_get_baudrate(...
它将同时导致整个EUSAT系统的复位。另一种类型的错误是CaldodoVrun错误。接收FIFO可以保存两个字符。如果...