/dev/ttyUSB0- 大多数 USB 转串行线将使用类似这样的文件显示。 /dev/pts/0- 伪终端。 Arduino 串行端口显示为 /dev/ttyACM0 (2) 开启/关闭串口 首先需要包含的头文件如下所示: #include <stdio.h> #include <string.h> // Linux headers #include <fcntl.h> // Contains file controls like O_RDWR...
UartDev 在 rom 代码中定义和初始化。extern UartDevice UartDev;本地结构 UartBuffer* pTxBuffer =...
1.4.2.2.uart_flow_ctrl_deinit 关闭流控。当调uart_deinit关闭串口时会调用该函数关闭硬件流。 原型: s32uart_flow_ctrl_deinit(uart_devuart_num); 参数: uart_num 串口号 返回值 0:成功,<0:失败 1.4.3.串口资源占用打印 1.4.3.1.uart_dump ...
ts_uart r init.rc 1500000 0 0 0 /dev/ttyS0 4.1 测试发送 测试发送的命令如下,send_0x55和send_00_ff为发送的文件: ./data/ts_uart.uart s ./data/send_0x55 1500000 0 0 0 /dev/ttyS3./data/ts_uart.uart s ./data/send_00_ff 1500000 0 0 0 /dev/ttyS3 发送成功可以通过USB转UAR...
UART4: /dev/ttyS4 ... 2.5 使用串口唤醒系统 串口唤醒系统功能是在系统待机时串口保持打开,并且把串口中断设置为唤醒源。使用时需要在dts中增 加以下参数: &uart1 { wakeup-source; }; 3. 控制台串口 在ArmSoM-Sige7中,UART2是作为控制台串口使用,可供用户查看开机启动的信息以及日常调试使用。
typedefenum{UART_BAUDRATE_300 =0, UART_BAUDRATE_600, UART_BAUDRATE_1200, UART_...
uint8_t flow_ctrl; uint8_t tx_fifo_threshold; uint8_t rx_fifo_threshold; }; 2.bflb_uart_init 说明: 初始化 uart。使用之前需要开启 uart ip 时钟、设置 uart 时钟源和分频值、选择 gpio 为 uart 中的一个功能。 void bflb_uart_init(struct bflb_device_s *dev, const struct bflb_uart_co...
uint8_t flow_ctrl; uint8_t tx_fifo_threshold; uint8_t rx_fifo_threshold; }; 2.bflb_uart_init 说明: 初始化 uart。使用之前需要开启 uart ip 时钟、设置 uart 时钟源和分频值、选择 gpio 为 uart 中的一个功能。 void bflb_uart_init(struct bflb_device_s *dev, const struct bflb_uart_co...
uint8_t flow_ctrl; uint8_t tx_fifo_threshold; uint8_t rx_fifo_threshold; }; 2.bflb_uart_init 说明: 初始化 uart。使用之前需要开启 uart ip 时钟、设置 uart 时钟源和分频值、选择 gpio 为 uart 中的一个功能。 void bflb_uart_init(struct bflb_device_s *dev, const struct bflb_uart_co...
FlowControlOp FlowControlQueue FlowControlQueues FormatBufferSetting FormatCallback FormatFrame FormatOutputConfig FormatSource FTW GfxFuncs GfxOpt glob_t GrallocBuffer GrallocFuncs HdfChipDriver HdfChipDriverFactory HdfChipDriverManager HdfDevEventlistener HdfDeviceIoClient HdfDevice...