一、裸机运行 在这种情况下,需要维护的时间仅有SYS Timebase Source,也就是HAL库中的 uwTick,这是HAL库中维护的一个全局变量,比如在 stm32f1xx_hal.c/stm32f4xx_hal.c 等不同系列的文件中都有如下定义: __IO uint32_t uwTick; 在CubeMX 配置界面中关于 SYS Timebase Source 的选择部分,如下图所示: ...
一、裸机运行 在这种情况下,需要维护的时间仅有SYS Timebase Source,也就是HAL库中的 uwTick,这是HAL库中维护的一个全局变量,比如在 stm32f1xx_hal.c/stm32f4xx_hal.c 等不同系列的文件中都有如下定义: __IO uint32_t uwTick; 在CubeMX 配置界面中关于 SYS Timebase Source 的选择部分,如下图所示: ...
Resume the time base source interrupt恢复时基源中断 基线恢复电路,电脑主板复位电路工作原理导语:复位电路在主板的设计当中以无可替换的必须品存在的,由于CPU的PG信号和复位信号都是由复位电路供给的。下面就来看看小编为大家整理的电脑硬件知识,希望对您有所帮助!一
Timebase source 时基解释评分: (RTOS笔记2)Timebase source 时基解释 一.软硬件版本信息:二.时基1.为什么要有时基2.裸机运行(1)默认配置SysTick(2)使用TIM1配置3.有操作系统三.总结 一.软硬件版本信息: STM32Cube Mx 5.30 Keil 5.29.0.0 STM32H750XB 二.时基 裸机运行时只需要维护一个时基就可以了,在加...
when FreeRtos is used.It is strongly recommended to use a HAL timebase source other than the Systic 在stmcubeMX中进行配置的时候,如果使用了freertos系统,生成代码的时候会有如下提示: 其意思就是,当使用了FreeRtos的时候,强烈建议HAL库使用除了Systick以外的时钟源。也就是说当不使用FreeRtos的时候,HAL...
func CMTimebaseCreateWithSourceClock(allocator: CFAllocator?, sourceClock: CMClock, timebaseOut: UnsafeMutablePointer<CMTimebase?>) -> OSStatus func CMTimebaseCreateWithSourceTimebase(allocator: CFAllocator?, sourceTimebase: CMTimebase, timebaseOut: UnsafeMutablePointer<CMTime...
2019-12-11 09:54 − 创建工程RTOS_BinarySem, 配置HCLK,使用内部晶振,频率为180MHZ(根据板子设置) 将SYS中时基源(Timebase Source)改为除SysTick之外的任意定时器即可,如: 配置FreeRTOS,使用CMSIS_V... 飞起的小田 0 1880 STM32CubeIDE+FreeRTOS互斥量实验 2019-12-11 16:53 − 在FreeRTOS 操...
func CMTimebaseCreateWithSourceTimebase(allocator: CFAllocator?, sourceTimebase: CMTimebase, timebaseOut: UnsafeMutablePointer<CMTimebase?>) -> OSStatus Creates a timebase by using a source timebase. Current page is CMTimebaseCreateWithSourceClock(allocator:sourceClock:timebase...
* If a source file does not specify a duration, but does specify * a bitrate, this value will be estimated from bitrate and file size. */ int64_t duration; 从上面的信息可以看到,AVStream->time_base单位为秒。 那AVStream->time_base具体的值是多少呢?下面以mpegts_demuxer为例: ...
optionally set trigger input source as Timer TIx in TIMx_SMCR reg - write TS bits Enable channel in TIMx_CCER reg - set CCEx bit If ETR is to be input clock: set clock mode2 in TIMx_SMCR reg - set ECE=1 configure prescaler, filter, polarity ...