步骤1:检查现有VLAN列表 执行display vlan summary命令,查看输出结果中“static vlan”字段下的VLAN列表。若目标VLAN未出现在列表中,则说明该VLAN未被创建。 步骤2:创建目标VLAN 在系统视图下执行vlan vlan-id命令(例如vlan 10),创建对应的VLAN。创建后,可通过display vlan命令...
当你在配置网络设备(如交换机)时遇到“error: the vlan does not exist”的错误,这通常意味着你尝试将一个接口分配到一个尚未在设备上创建的VLAN中。以下是一些解决此问题的步骤,你可以按照这些步骤逐一检查并解决问题: 1. 确认VLAN配置环境 首先,确保你正在正确的设备上执行VLAN配置。检查设备型号、操作系统版本和...
Error: The VLAN does not exist. 设备上没有创建相应的VLAN。 可执行命令display vlan summary,检查“static vlan”字段下的VLAN中是否存在与待创建的VLANIF接口对应的VLAN。 执行命令vlanvlan-id,创建与VLANIF接口对应的VLAN,然后再创建指定的VLANIF接口。
Error: The VLAN does not exist. 设备上没有创建相应的VLAN。 可执行命令display vlan summary,检查“Static vlan”字段下的VLAN中是否存在与待创建的VLANIF接口对应的VLAN。 执行命令vlanvlan-id,创建与VLANIF接口对应的VLAN,然后再创建指定的VLANIF接口。
VLAN的总数为4096个,范围0-4095,能够使用的VLAN编号为1-4094 所有的配置需要事先进入system-view [HXY-Sw1-GigabitEthernet0/0/6]port default vlan 100 Error: The VLAN does not exist.---漏了相应VLAN的创建配置 一个内部同一个VLAN的设备如果需要跨交换机通信, 将交换机之间的接口配置为trunk(跟着自己实...
请使用其他的IP地址进行配置。错误提示信息十：Error: The VLAN has a L3 interface. Please delete it first.错误提示信息解释：undo vlan的时候要先undo vlanif故障排除方法：undo vlanif 10 #华为认证# 等等！！！【关注私信我们】 拿华为认证免费刷题题库 数量有限！只有30个名额！快关注我们吧！
git_not_command– fixes wrong git commands likegit brnch; git_pull– sets upstream before executing previousgit pull; git_pull_clone– clones instead of pulling when the repo does not exist; git_pull_uncommitted_changes– stashes changes before pulling and pops them afterwards; ...
ARP Monitoring appears to fail when a bond is stacked with a VLAN and a bridge. For example if a bridge is configured on top of bondX interface(with ARP link monitoring) then the issue isn't observed, its only observed if a bridge is configured on top of bondX.vlan interface (with ...
VLAN tagging not working VM in hyper-v manager infinite reboot loop issue VMDK to VHD Conversion VMware Snapshot Provider and VSS writer timeouts (Event ID 8193) Volume C: (\Device\HarddiskVolume6) needs to be taken offline to perform a Full Chkdsk. Please run "CHKDSK /F" loca...
In direct forwarding mode, VLAN configuration must be allowed on the switch connected to APs. Do not connect APs to the switch that does not support VLAN configuration. In the following example, VLAN 10 and VLAN 20 are configured as the management VLAN and service VLAN respectively on the ...