Tensile Strength, ksi 青云英语翻译 请在下面的文本框内输入文字,然后点击开始翻译按钮进行翻译,如果您看不到结果,请重新翻译! 翻译结果1翻译结果2翻译结果3翻译结果4翻译结果5 翻译结果1复制译文编辑译文朗读译文返回顶部 拉伸强度,KSI 翻译结果2复制译文编辑译文朗读译文返回顶部...
Designation: A325 − 14American AssociationState Highway andTransportation OfficialsStandard AASHTO No.: M 164Standard Specification forStructural Bolts, Steel, Heat Treated, 120/105 ksi MinimumTensile Strength1This standard is issued under the fixed designation A325; the number immediately following the...
Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strengthdoi:ASTM A325-04a1.1本规范涵盖两种类型的淬火和回火钢结构螺栓,尺寸为1.0英寸,最小抗拉强度为120 ksi.尺寸大于1.0至1英寸时小于105 ksi.,包含全部费用\n1.2螺栓用于结构连接.这些连接件包含在使用ASTM A ...
(4.3.5)Su(ksi)=0.5BHN The ultimate tensile strength for cast iron can be estimated (Krause, 1969) as (4.3.6)Su(MPa)=1.58BHN−86 or (4.3.7)Su(ksi)=0.23BHN−12.5 View chapter Book 2005, Fatigue Testing and AnalysisYUNG-LI LEE, DARRYL TAYLOR ...
functional spline length 6.15 Chosen spline length s 0,005 Lmin 1,251 L 1,375 [in] [in] [in] 7.0 Strength checks of the coupling 7.1 Check of shaft for torsion 7.2 Permitted stress in shear 7.3 Comparative stress 7.4 Safety τA 30 [ksi] τ 10,5 [ksi] 2,87 7.5 Check of ...
150 Ksi Steel Grades High Tensile Strength All-Thread Bar Threaded Rod US$0.10-3.00 1,000 Pieces (MOQ) Product Details Customization: Available Material: Carbon Steel Surface Finishing: Zinc PlatedContact Supplier Chat Still deciding? Get samples of US$ 1/Piece ! R...
PURPOSE: A method for manufacturing ultra-high tensile strength steel having 220 ksi class yield strength is provided to lower the minimum addition amount of expensive Co to 9.5% level by applying direct quenching right after hot rolling and simplify manufacturing facility and remove environment pollut...
Tensile Strength, psi Elongation, % Sample Identification Specimen Width, in Thickness, in Peak Load, lbf at Yield at Break at Yield at Break Modulus, ksi 1 0.499 0.261 219 1542 1680 7.17 68.4 62.1 2 0.492 0.299 227 1455 1543 7.56 61.4 55.7 ...
mrmyagi, While that sounds reasonable, vessels often buckle and collapse in fire because both the strength and modulus are dropping. They can't support themselves, though they may still hold pressure. You cannot extrapolate high temp data as it isn't linear. At a stress of 5.5ksi you are ...
where Fy is the yield strength, in ksi (MPa). View chapter Book 2020, Offshore Structures (Second Edition)Mohamed Abdallah El-Reedy Ph.D. Chapter Design loads and casing selection 4.5 Axial loads and design plot We did not consider axial loads at the time we made our collapse and burst ...