当数据再被往下传输的时候,就变成了packet,即“包”的意思。在这一层,Segment会被加上IP头部信息,然后就可以在三层传输了,而工作在三层的路由器会根据目的IP地址来转发这些”包“。 在往下,数据就会被加上MAC地址信息,名称就变成了Frame,”帧“。在这一层,就是交换机的世界了,交换机通常查找MAC地址表项来转发...
SEQ_NUM 代表 TCP header 中的 Sequence number ACK_NUM 代表 TCP header 中的 Acknowledgment number DATA_LEN 代表 segment 中 data 的长度 代码语言:javascript 代码运行次数:0 运行 AI代码解释 SYN(1)ACK(0)SEQ_NUM(0)ACK_NUM(0)DATA_LEN(0)===><===SYN(1)ACK(1)SEQ_NUM(100)ACK_NUM(1)DATA_...
TCP包的序号与接收窗口的行为很像时钟。 TCP sequence numbers and receive windows behave very much like a clock. The receive window shifts each time the receiver receives and acknowledges a new segment of data. Once it runs out of sequence numbers, the sequence number loops back to 0. 连接终止...
Header format for TCP: Header format for TCP is shown below: TCP Header Format Source Port: It is 16 bits in length and defines port of the source TCP user. Like HTTP has 80 port number. Destination Port: It is also 16 bits in length and tells the port of the destination TCP user....
(1)TCP将若干个字节构成一个分组,叫报文段(Segment) (2)TCP报文段封装在IP数据报中 (1)端口号:用来标识同一台计算机的不同的应用进程。 (2)源端口:源端口和IP地址的作用是标识报文的返回地址。 (3)目的端口:端口指明接收方计算机上的应用程序接口。
which is the byte ordering required for all binary integers in the TCP/IP headers as they traverse a network. This is called the network byte order. Machines that store binary integers in other formats, such as the little endian format, must convert the header values into the network byte ...
从大型 TCP 数据包派生的段数据包数量必须等于或大于微型端口驱动程序指定的MinSegmentCount值。 有关MinSegmentCount值的详细信息,请参阅报告 NIC 的 LSOv1 TCP 数据包分段功能和报告 NIC 的 LSOv2 TCP 数据包分段功能。 以下假设和限制适用于处理任何支持 LSO 的微型端口驱动程序(无论版本如何)的 IP ...
●Header checksum(头部校验和字段):占16比特,内容是根据IP头部计算得到的校验和码。计算方法是:对头部中每个16比特进行二进制反码求和。(和ICMP、IGMP、TCP、UDP不同,IP不对头部后的数据进行校验)。 ●source address&&Dest address:源地址和目的地址,各占32字节,当然这个是针对的IPV4 ...
Destination Address:目标 IP 地址。 再来看看TCP 包segment: 图片来源:http://www.tcpipguide.com/free/t_TCPMessageSegmentFormat-3.htm TCP 包也分为头部和数据两部分。头部包含最少20个字节的数据。 TCP 包有以下 header 字段: Source Port:源端口。 Destination Port:目标端口。 Sequence Number:序列号,每个...
一、如何区分TCP连接是主动断开还是异常断开 主动断开:active RST,根据协议来看,如果断开一个预期的TCP连接,RST seq会使用ack的seq填充到RST-ack字段中,如下截图: RST对应发起位置如下: 函数内部调用逻辑如下: tcp_send_active_reset() -> skb = alloc_skb(MAX_TCP_HEADER, priority); ...