开始玩HA翻出来,拆掉看了下是ESP32C2-02主控,闲着也是闲着,直接换固件吧,翻出杜邦线,接好了VCC,GND,RXD,TXD,BOOT,其中boot引脚在背面如上图,另一头接入CH340,BOOT接地,就可以刷机了。 发现ESPhome不支持c2,tasmota也明确不支持c2,能支持的就只有haa了,刷了haa,仔细学习引脚定义。 https://
空气净化器示例,利用ESP32-C2透传固件,低成本、高效连接传统设备,实现智能控制 337 0 02:23 App 如何使用ESP32-C3透传固件快速将暖风机接入物联网平台实现智能控制 912 0 00:59 App 实测openai-realtime-embedded-sdk在ESP32-S3实时对话,延迟在500ms左右 206 0 02:53 App 基于ESP32-S3的人工智能终端,...
ESPC2-02 technical specification ESP32-C2 chip For smart plug firmware flash ESPC2_02 << < 1 > >> ABLOUT US Technology change life. Creative sci-fi lifestyle enjoy a good life can flash firmware Base on Tasmota esphome with any chip and any custom your PCBA and any custom ...
tasmota32.bin http://ota.tasmota.com/tasmota32/tasmota32.bin 2045k 20250606 17:19 tasmota32c2.bin http://ota.tasmota.com/tasmota32/tasmota32c2.bin 1916k 20250606 17:19 tasmota32c3.bin http://ota.tasmota.com/tasmota32/tasmota32c3.bin 2049k 20250606 17:19 tasmota32c6.bin http://ota.ta...
# Tasmota Platformio Arduino for ESP32, ESP32-S2, ESP32-S3, ESP32-C2, ESP32-C3, ESP32-C6 and ESP32-H2 2 2 3 - [](https://github.com/espressif/arduino-esp...
ESP32, ESP32-C2, ESP32-C3, ESP32-C6, ESP32-S2 and ESP32-S3 based The following binary downloads have been compiled with ESP32/Arduino library core versionv3.1.1.250203. tasmota32.bin= The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash.RECOMMENDED RELE...
platform_packages=${core32.platform_packages} board_build.filesystem=${common.board_build.filesystem} custom_unpack_dir=${common.custom_unpack_dir} board_build.variants_dir=${common.board_build.variants_dir} board=esp32 monitor_speed=${common.monitor_speed} ...
ESP32-C3 OTA binary name from tasmota32c3cdc.bin to tasmota32c3.bin with USB HWCDC and fallback to serial (#21212) ESP32-C6 OTA binary name from tasmota32c6cdc.bin to tasmota32c6.bin with USB HWCDC and fallback to serial (#21212) ESP32-S3 OTA binary name from tasmota32s3cdc.bi...
基于ESP32-C2 ,同时支持CozyLife +HomeAssitant,提供标准的MQTT接入,包括设备发现,控制,状态上报,可以平替 Tasmota、ESPHome等软件生态通断器 - 四博真选于20241113发布在抖音,已经收获了7.3万个喜欢,来抖音,记录美好生活!
You just need to solder a 4-pin 2.54mm pitch header, connect the board, and use esptool to flash the image. One it’s done you can simply remove the wire, leave the header in place, and put the case back in place. But with Sonoff B1 light bulb, it’s not quite as easy. First...