port Enter the port number on the remote IP address for the TACACS server Default: 49 Values: 1645 | 1812 state Enable or disable this configured TACACS server Default: enabled Values: enabled | disabled secret Enter the password the TACACS server and the Oracle Communications Sessi...
ChallengeResponse=DES(ServerChallenge,KEY);challenge一般为8字节 图2-4-5-3 ARAP authentication组成 2.5 TACACS+数据包的加密 TACACS+支持除包头之外所有信息的加密,加密方法如下: 1) 将session_id、secret key, 版本号和sequence number一起进行MD5运算(其中secret key 为TACACS客户端和服务器之间的共享秘密),计...
tacacs-server host {server-name | ip-address} [key [0|7] shared-secret] [port port-number] [timeout seconds] no tacacs-server host {server-name | ip-address} [key [0|7] shared-secret] [port port-number] [timeout seconds] Syntax Description server-name ip-address key 0 7 shared ...
In the server template, specify the IP address, port number (49 by default), and shared key of the server connected to the switch. The configuration of the switch must be the same as that of the server. # hwtacacs-server template t1 hwtacacs-server authentication 10.1.1.2 hwtacacs-server ...
ChallengeResponse=DES(ServerChallenge,KEY);challenge一般为8字节 图2-4-5-3 ARAP authentication组成 2.5 TACACS+数据包的加密 TACACS+支持除包头之外所有信息的加密,加密方法如下: 1) 将session_id、secret key, 版本号和sequence number一起进行MD5运算(其中secret key 为TACACS客户端和服务器之间的共享秘密),计...
server-private {ip-address | name} [nat] [single-connection] [port port-number] [timeout seconds] [key [0 | 7]string] 12. ipvrfforwarding vrf-name 13. iptacacssource-interface subinterface-name 14. exit コマンドまたはアクション enable 例: Device> enable configure terminal ...
AAA⼀般采⽤客户机/服务器结构，客户端运⾏于NAS（Network Access Server，⽹络接⼊服务器）上，服务器上则集中管理⽤户信息。NAS对于⽤户来讲是服务器端，对于服务器来说是客户端。AAA的基本组⽹结构如下图：当⽤户想要通过某⽹络与NAS建⽴连接，从⽽获得访问其它⽹络的权利或取得某些⽹...
1.1 什么是TACACS+ TACACS+（Terminal Access Controller Access Control System，终端访问控制器控制系统协议）是在TACACS协议的基础上进⾏了功能增强的安全协议。该协议与RADIUS协议的功能类似，采⽤客户端/服务器模式实现NAS与TACACS+服务器之间的通信。1.2 TACACS+的⽤途 TACACS+协议主要⽤于PPP和VPDN（...
tacacs-server host 1.2.3.4 key 7 "dxg123" port 1 timeout 1 single-connection Note: The property information for this example was added in Release 9.3(3). Verifying a DME ConfigurationThe following table contains the distinguished name (DN) for each managed obj...
The port to use for communication between the TACACS+ server and client. By default, Cumulus Linux uses IP port 49. The TACACS timeout value, which is the number of seconds to wait for a response from the TACACS+ server before trying the next TACACS+ server. You can specify a value bet...