1.查看centos中是否安装了openssh-server。查看命令:yum list installed | grep openssh-server 上图显示已经安装,如果没任何输出显示表示没有安装 openssh-server,通过输入 yum install openssh-server来安装。 2.修改 /etc/ssh/ 目录下的sshd服务配置文件 sshd_config。(注意一定是sshd_config文件,如果系统中安装...
enabled 开机自启的状态。 也可以通过 systemctl list-unit-files | grep sshd 只列出 sshd 的开机启动的状态。 tips:红帽 5 和 6 查看服务状态是:Service sshd status。 开机自启是:Chkconfig ssh on/off。
systemctl list-units –type=service –all grep cpu 列出 cpu电源管理机制的服务 systemctl list-units –type=target –all 列出所有target 3、systemctl特殊的用法 systemctl命令 说明 systemctl is-active [unit type] 查看服务是否运行 systemctl is-enable [unit type] 查看服务是否设置为开机启动 systemctl...
systemctl status firewalld.service 在开机时启用一个服务:systemctl enable firewalld.service 在开机时禁用一个服务:systemctl disable firewalld.service 查看服务是否开机启动:systemctl is-enabled firewalld.service 查看已启动的服务列表:systemctl list-unit-files|grep enabled 查看启动失败的服务列表:system...
systemctl list-units --type=service #查看所有已启动的服务 systemctl list-unit-files |grepnginx #查看是否正确启动 sudo systemctl daemon-reload #刷新配置system目录 二、相关配置 下面nginx.service文件配置,复制到/etc/systemd/system或者/usr/lib/systemd/system目录下 ...
2,直接grep systemctl list-units --type=service | grep running 三,列出所有自启动的服务 1,列出所有自启动的单元 除了服务,还包括:socket/target/timer systemctl list-unit-files --state=enabled 2,列出所有自启动的服务 systemctl list-unit-files --type=service --state=enabled...
systemctl list-unit-files|grep firewalld 列出所有服务的层级和依赖关系,可以指定某个服务systemctl list-dependencies [服务名称] CentOS 7.x开始 CentOS开始使用systemd服务来代替daemon,原来管理系统启动和管理系统服务的相关命令全部由systemctl命令来代替。 1、原来的 service 命令与 systemctl 命令对比 service ...
systemctl list-unit-files [ | grep 服务名](查看服务开机启动状态,grep可以进行过滤) systemctl enable 服务名(设置服务开机启动),对3(无界面)和5(GUI)运行级别都生效 systemctl disable 服务名(关闭服务开机启动),对3(无界面)和5(GUI)运行级别都生效 ...
❯ systemctl list-unit-files | grep home systemd-homed-activate.service disabled disabled systemd-homed.service disabled enabled ❯ systemctl enable systemd-homed Created symlink /etc/systemd/system/dbus-org.freedesktop.home1.service → /usr/lib/systemd/system/systemd-homed.service. ...
there are roughly 4000 of those leaked scope units and list-unit-files takes about 23 seconds. During that time, further ssh logins are delayed until the command terminates. When I used ; instead of & in the loop doing the ssh logins, I was unable to reproduce the issue, so it looks ...