(including eth_type_trans()) */ /* Interface address info used in eth_type_trans() */ // 网络设备接口的MAC地址 const unsigned char *dev_addr; // 接收队列 struct netdev_rx_queue *_rx; // 接受队列个数 unsigned int num_rx_queues; // 设备中当前是activate的队列数 unsigned int real_...
1inteth_header(structsk_buff *skb,structnet_device *dev, u16 type,void*daddr,void*saddr,intlen)2{3//将skb->data = skb->data + ETH_ALEN;4structethhdr *eth = (structethhdr*)skb_push(skb, ETH_ALEN);56if(type !=ETH_P_802_3)7eth->proto = htons(type);//htons()将本地类型转换...
void phy_connect_dev(struct phy_device *phydev, struct eth_device *dev); struct phy_device *phy_connect(struct mii_dev *bus, int addr, struct eth_device *dev, phy_interface_t interface); static inline ofnode phy_get_ofnode(struct phy_device *phydev) ...
int(*set_wol)(struct phy_device *dev, struct ethtool_wolinfo *wol); void(*get_wol)(struct phy_device *dev, struct ethtool_wolinfo *wol); void(*link_change_notify)(struct phy_device *dev); int(*read_mmd)(struct phy_device *dev,intdevnum, u16 regnum); int(*write_mmd)(struct p...
int eth_header(struct sk_buff *skb, struct net_device *dev, u16 type, void *daddr, void *saddr, unsigned len) EXPORT_SYMBOL(eth_header); skb : 将要去修改的struct sk_buff; dev : 原网络设备 type: 网络层的协议类型 daddr:目的MAC地址 ...
structrte_eth_txconf default_txconf;/**< 默认发送队列配置 */ structrte_pci_device*pci_dev;/**< 对应的PCI设备信息 */ uint32_tvmdq_pool_base;/**< 第一个VMDq池的ID */ uint32_tvmdq_pool_size;/**< 每个VMDq池支持的最大队列数量 */ ...
这里需要说明,虽然使用 calico 的 ipip 模式,由于 pod 的访问为 service 的 nodePort 模式,所以不会走 tunl0 网卡,而是从 eth0 经过 iptables 后,通过路由到 calico 的 calixxx 接口,最后到 pod。 3.2 性能分析 在上面压测结果的图中,我们容器化后,CPU 的软中断si使用率明显高于原先虚拟机的si使用率,所以...
structrte_eth_intr_conf intr_conf; /**< Device interrupt configuration. */ }; 具体解析如下: link_speed: 设备的链接速度,取值范围为 Ethernet 链接速率,如 ETH_LINK_SPEED_10M。 link_duplex: 设备的链接双工模式,取值范围为 ETH_LINK_HALF_DUPLEX 和 ETH_LINK_FULL_DUPLEX。
1//hook函数由 指定,其函数声明如下: nf_hookfn *hook23//include/linux/netfilter.h45typedef unsignedintnf_hookfn(unsignedinthooknum,6structsk_buff *skb,7conststructnet_device *in,8conststructnet_device *out,9int(*okfn)(structsk_buff *)); ...
备的net_device结构。而虚拟设备驱动会在一组设备中选择一个设备并把dev指针修改为这个设备的net_device结构。因此,在某些情况下,指向传输设备的指针会在包处理过程中被改变。 sk_buff->input_dev 这是收到包的网络设备的指针。如果包是本地生成的,这个值为NULL。对以太网设备来说,这个值由eth_type_trans初始化...