Core-Sw1(config)# spanning-tree etherchannel guard misconfig 企业还应该在连接至服务器的所有接入交换机端口上使用根保护机制(Root Guard)。 激活这项功能的思科IOS接口配置命令如下: Core-Sw1(config-if)# spanning-tree guard root 有时候,刀片服务器嵌入了以太网交换机,这类服务器也应该考虑到STP设计和配置...
1. 接入交换机到核心交换机的接口 根保护(Root Guard):建议在接入交换机到核心交换机的接口上配置根保护。根保护可以防止接入交换机错误地成为根桥,从而保持网络拓扑的稳定性。 环路保护(Loop Guard):同样建议在这些接口上配置环路保护。环路保护可以防止由于链路故障或BPDU丢失导致的环路形成。 2. 接入交换机到PC的...
要防止此问题,可以在接入端口激活BPDU Guard和Root Guard来监控是否有BPDU进入。它们的基本操作如下: 1)BPDU Guard:在每个或者单个端口上激活;如果接收到任何BPDU,该端口即被屏蔽。用来防止对交换机STP的DOS攻击,需要配置errdisable后可自动恢复。 #errdisablerecovery causebpduguard #errdisablerecovery interval 30指定...
Core-Sw1(config)# spanning-tree etherchannel guard misconfig 企业还应该在连接至服务器的所有接入交换机端口上使用根保护机制(Root Guard)。 激活这项功能的思科IOS接口配置命令如下: Core-Sw1(config-if)# spanning-tree guard root 有时候,刀片服务器嵌入了以太网交换机,这类服务器也应该考虑到STP设计和配置...
The administrator designates the boundary ports as "root guard protected" ports (RG ports). The STP then executes as required by the ordinary STP protocol, and if a RG port is selected by the STP to be a root portm then the status of the port is set to "blocked," and no packets ...
通过上面的实验,发现root guard的重要性了吧,现在开始配置这一功能 在SW2上的E0/2口开启(因为e0/0 -1两个口,正在运行着STP,且之前已经收敛完成了)实际中应该在root设备上所有未使用的接口都配置根防护,从而“把根留住” 先把SW1的e0/0口shudown,(等同于拔掉网线) ...
Root Guard用于防止意外的根桥选举,确保网络的根桥稳定。当启用Root Guard的端口收到优于当前根桥的BPDU时,端口会进入阻塞状态,防止该端口成为新的根端口。 # 启用Root Guardinterface [interface-id] spanning-tree guard root Root Guard通常用于网络边界,确保核心交换机始终作为根桥。
应该在所有不应出现根桥的端口上启用STP Root Guard 特性,这样做保护了当前主根桥和备根桥的选择。 单向链路检测(UDLD)提供了一种检测单向传输链路的方法,使得STP无法常规检测出来或阻止的路由环路和流量黑洞得以防止。 工作在2层的UDLD发送含有设备ID与端口ID的数据包至交换机端口所连的邻居设备。
an dem Root Guard aktiviert ist, höherrangige STP-Bridge-Protokoll-Dateneinheiten (BPDUs) empfängt, weist Root Guard diesem Port den Status "Root inkonsistent" zu. Der Status "Root inkonsistent" entspricht effektiv einem Mithörstatus. Über diesen Port wird kein Verkehr weitergeleit...
STP根保护(Root Guard)特性用来在交换网络内强制根桥位置及身份。在端口启用了Root Guard特性后,如果该端口收到了更优的BPDU,那么Root Guard将停用此端口。此技术用于避免其他交换机意外地成为根桥。 应该在所有不应出现根桥的端口上启用STP Root Guard 特性,...