启动串口1数据发送的代码: 1voidUart1_RS232_SendString(unsignedchar*buf,unsignedcharlen)2{3if(len >=MAX_TX1_BUFSIZE)4len =MAX_TX1_BUFSIZE;56memcpy(uart1_tx_buf,buf,len);7uart1_tx_SendLength =len;89USART_ITConfig(USART1,USART_IT_TXE,ENABLE);//这里立即启动了发送中断10} 串口1的中断函数:...
5. USART_IT_CTS : specifies the interrupt sourceforthe CTS interrupt. 6. USART_IT_LBD : specifies the interrupt sourceforthe LIN break detection interrupt. 7. USART_IT_PE : specifies the interrupt sourceforthe parityerrorinterrupt. 8. USART_IT_ERR : specifies the interrupt sourceforthe error...
USART_InitClockStructure.USART_Clock = USART_Clock_Disable; USART_ClockInit(USART1, &USART_InitClockStructure); */ USART_Cmd(USART1, ENABLE); USART_ITConfig(USART1, USART_IT_RXNE,ENABLE); //先使能接收中断; USART_ITConfig(USART1, USART_IT_TXE,DISABLE); //先禁止发送中断; while(1) { //...
中断(输出)控制,申请中断位就是状态寄存器SR的各种标志位,其中TXE发送寄存器空和RXNE接收寄存器非空比较重要,是必要的。中断控制就是配置中断是否可以通向NVIC。 最下面为波特率发生器部分,波特率发生器其实就是分频器,APB时钟进行分频,得到发送和接收移位的时钟。时钟输入是fPCLKx(x=1或2),USART1挂载在APB2上所以...
{USART_ITConfig(USART1, USART_IT_TXE, ENABLE);} } void USART_puts(u8 *str){ while(*str !
USART_ITConfig(USART3, USART_IT_TXE, DISABLE);//因为是 发送寄存器空 的中断,所以发完字符串后...
USART_GetFlagStatus(USART1, USART_FLAG_RXNE); 要判断发送是否成(T完C),操作库函数的方法是: USART_GetFlagStatus(USART1, USART_FLAG_TC); 以上这些标识号在 MDK 里面是通过宏定义定义的: 1 #define USART_IT_PE ((uint16_t)0x0028) 2 #define USART_IT_TXE ((uint16_t)0x0727) ...
🔧 使能USART通讯。 🔧 使用USART_SendData发送数据,使用USART_ReceiveData接收数据。 🔧 若需接收数据,需设置接收中断服务函数。 🔧 了解标志位信息: USART_IT_RXNE:接收中断标志位,当该位被设置时表示可以接收数据。 USART_FLAG_TXE:发送标志位,当该位被设置时表示发送完毕,可以写入下一个数据。0...
uint16_t USART_Parity; /*!< Specifies the parity mode. This parameter can be a value of @ref USART_Parity @note When parity is enabled, the computed parity is inserted at the MSB position of the transmitted data (9th bit when
01. USART固件库概述 stm32f4xx_usart.h 函数的声明和类型的声明 stm32f4xx_usart.c 函数的实现 02. USART相关类型 stm32f4xx_usart.h文件中 USART_InitTypeDef类型 /** * @brief USART Init Structure definition */ typedef struct { uint32_t USART_BaudRate; /*!< This member configures the USART ...