STM32CubeMX 是用于 32 位 ARM Cortex STM32 微控制器的图形工具。它允许对 STM32 微控制器和微处理器进行非常简单的配置,生成初始化 C 代码,还可以通过一步一步的操作为 Arm Cortex-M 内核或 Arm Cortex-A core 生成部分 Linux 设备树。它是 STMCube 生态系统的一部分,且可以作为独立应用程序或作为 ...
// <o1.13> DBG_TIM4_STOP Timer 4 Stopped when Core is halted31. // <o1....
../Core/Src/main.c:382:13: warning: 'MX_USART1_UART_Init' defined but not used [-Wunused-function] 7. Open main.c file, create the prototype of Prime_Calc_SRAM() function which is in charge of computing prime number in an array.Note: This function is defined...
that counts down from the reload value to zero, reloads (wraps to) the value in the STK_LOAD register on the next clock edge, then counts down on subsequent clocks. When the processor is halted for debugging the counter does not decrement. ...
锁定(Lockup)[注]和停机(Halted)状态指示处理器进入了锁定状态(由在硬fault和 2 (LOCKUP,HALTED)NMI服务例程的执行错误导致),或者指示处理 器被喊停(因为调试动作导致) 端输入(ENDIAN)在内核复位时设置端模式 ETM接口连接到嵌入式宏单元(用于指令) ITM的ATB接口高级总线(ATB)是ARMCoreSight调试架 构下的一个总...
// <o1.12> DBG_TIM3_STOP Timer 3 Stopped when Core is halted // <o1.13> DBG_TIM4_STOP Timer 4 Stopped when Core is halted // <o1.14> DBG_CAN_STOP CAN Stopped when Core is halted // </h> _WDWORD(0xE0042004,0x00000027);// DBGMCU_CR _WDWORD(0xE000...
It is possible to disable debugging completely, by setting ROP/RDP Level == 2. A connect will not be possible anymore afterwards and the security cannot be reset. The device is briefly halted while checking security. This is done because in some cases, device security might be detected wrongl...
/***//** STM32的内核是ARM CORTEX-M3,这个core_cm3.h包含的是一些内核相关的和宏定义,例如核内寄存器定义、部分核内外设的地址等等,其对应的是core_cm3.c文件。 * @file core_cm3.h * @brief CMSIS Cortex-M3 Core Peripheral AccessLayer Header File外设接口进入头文件 微控制器软件接口标准(CMSIS...
[stm32f1x.cpu] halted due to debug-request, current mode: Thread xPSR: 0x01000000 pc: 0x08000188 msp: 0x20000708 ** Programming Started ** Info : device id = 0x10006412 Info : ignoring flash probed value, using configured bank size Info : flash size = 128 KiB Warn : Adding extra ...
找出并修改Core/Src/system_stm32f1xx.c以下内容(按手动加入的中文注释的提示操作): /* Note: Following vector table addresses must be defined in line with linker configuration. */ /*!< Uncomment the following line if you need to relocate the vector table anywhere in Flash or Sram, else the ...