PlatformIO 具有 Build、Upload、Upload to Remote Device、Clean、Test、Run Task、Serial Monitor、New Terminal等功能。所有功能都可以在编辑器的左下角找到。当您将鼠标悬停在图标上时,将显示功能。 要构建草图,请单击“构建”并上传草图,请单击“上传”图标。上传
同样,在脚本运行后,输入数字12,然后按下Enter键,以选择安装PlatformIO。 步骤3:安装VSCODE插件和SerialMonitor插件 打开安装好的Visual Studio Code。 打开VSCODE的插件商店: 在VSCODE的侧边栏中,点击“Extensions”图标,然后在搜索框中搜索“PlatformIO”,找到并安装PlatformIO插件。 安装SerialMonitor插件: 在VSCODE的侧边...
5. Arduino IDE或STM32CubeIDE(作为开发环境) 软件需求 1. STM32CubeMX - 用于配置STM32外设。 2. STM32CubeIDE - 用于编写和调试代码。 3. 串口监控工具(如PuTTY或Arduino Serial Monitor) - 用于观察调试信息。 此外小编还额外整理了许多关于stm32项目资料,欢迎大家点击链接加入裙聊免费薅羊毛~ STM32项目合...
(Serial Monitor window)按钮打开串口监视器,如果你的串口设置正确,就可以看到Maple通过虚拟USB串口传回的文字。 1.5.4 Maple IDE的使用 与Arduino IDE一样,Maple IDE也是在Processing IDE的基础上开发的,且简单易用,非常容易上手。下面对Maple IDE做一些简单的介绍。Maple IDE的界面主要有代码编辑区、工具栏和状态...
According to your suggestion, I added 12.5KOhm pull-up resistors to each SDA and SCL lines. However it is still printing "2" to the Serial monitor. Note that these resistors were absolutely unnecessary for an Arduino UNO to detect my MPU9250. ...
begin(115200); Serial.println("start."); } --- 原因:我想把Serail 重新定义指向 串口1.面上百度,CSDN,知乎均未找到正确可行的答案。(已解决) [env:genericSTM32F103RC] platform = ststm32 board = genericSTM32F103RC framework = arduino upload_protocol = stlink debug_tool = stlink monitor_speed ...
串口监视器按钮(Serial monitor):插头,点击后会启动命令行的串口监视助手; 终端按钮(New Terminal):命令行,新建一个终端窗口; 先来尝试一个使用吧,更多的功能,在实际的使用过程中再进行学习, 每次我的电脑点击新建工程后都会无法点击输入框,所以只好退出后重新进入 ...
下面所示的Arduino代码就是对库的例程进行修改所得到的,可以成功用在ESP32上。 #include #include #include // Enabe debug tracing to Serial port. #define DEBUGGING // Here we define a maximum framelength to 64 bytes. Default is 256. #define MAX_FRAME_LENGTH 64 ...
Step 4. Refer to step 4 - step 12 from the previous LoRaWAN® End Node application Step 5. Open a serial monitor such as Arduino Serial Monitor and you will see the following outputStep 6. Type AT? and press ENTER to view all the available AT commandsStep 7. If you still want to...
i then switch out of serial monitor on the host and run esptool to flash a rom on the esp8266. Again, this is literally beyond the scope of this document, but this note here is just a tip on how i did it successfully in one of the attempts....