1. STM32duino Bootloader 2. 串口 3. 通过使用 ST-Link 调试器 4. 通过BMP（黑魔法专业版）...
Type on Windows CMD (or Linux terminal)stm32flash.exe -g 0x8000000 -b 115200 -w hid_generic_pc13.bin COM2orstm32flash -g 0x8000000 -b 115200 -w hid_generic_pc13.bin /dev/ttyS0for programming the HID Bootloader firmware to aBluePillboard. Apply theArduino_STM32_patchfromherein case ...
Select from Arduino IDETools > Board > [your_stm32_board] SelectTools > Upload method > HID Bootloader 2.1or newer You are ready ! Normally, bothBOOT-0andBOOT-1must be connected to '0'. If you connectBOOT-1pin to 3.3V (or '1' on BluePill boards), the board will stay in HID Bo...
STM32 HID bootloader Bootloader for STM32F103 and STM32F4xx micro-controllers No special driver is required. Support for Windows, Linux and Mac Operating System 30 Topics 179 Posts Last post Re: STM32F103C8T6 BluePill+ e… by ag123 View the latest post Sat Jan 11, 2025 3:43 pm USB...
You can use "tkg-flash -info" to check the current bootloader firmware. You can also use CTRL + ALT + S within the Arduino IDE to get a binary in the tkg_hid_btl_uploader directory. Arduino IDE integration Quit Arduino IDE if active. First, to add a new upload method in the STM32...
stm32移植到arduino上开发 引脚图 下载和烧写Bootloder 首先我们要下载Bootloader,进入刚刚那个人的另一个开源项目,地址如下: https:///rogerclarkmelbourne/STM32duino-bootloader/tree/master/binaries 选择你的STM32最小系统板的除电源指示灯外的另一个LED所对应的接口名字的文件下载(一定要选择对应的),我的板子为...
使用Arduino为STM32F103C8T6编程安装Arduino软件下载并烧录bootloader安装串口支持特点STM32F103C8T6是一款ARM Cortex-M3系列的32位RISC hrtuoyu2021-08-11 08:25:28 使用Arduino开发STM32 这里写自定义目录标题环境说明使用Arduino开发STM32原因直接开始操作环境说明开发软件:vscode+PlatformIO操作系统:win10开发板:STM32...
目录一、ArduinoIDE 配置二、烧录.bin 文件三、程序实现四、总结五、参考资料本文内容:安装ArduinoIDE 和相关软件支持库,在Arduino完成STM32板子的串口 半导体开发2022-02-17 06:15:29 给Arduino烧录引导程序bootloader bootloader,Boot,Arduino,烧录 2022-03-01 16:57:20 ...
STM32F103可以通过USB接口与Arduino进行通信，但这种通信通常是通过USB串口（CDC）或USB HID（人机接口设备...
Selecting Upload method HID Bootloader 2.2 does not start any Bootloader. However I can use (DFU) if I unplug USB. Re-plug with MODE0 button pressed. So it appears that BOOT0 + RST does not start STM32 Bootloader reliably. I suspect that you might succeed after 100 attempts. And the ...