X-CUBE-TIM-32RES Achieving 32-bit timer resolution with software expansion for STM32Cube Data brief Features • 32-bit input capture mode example using link system • 32-bit input capture mode example using
The function HardwareTimer::setOverflow() allow to set the overflow value as a uint32_t an then set the value of the STM32 ARR Register to: o v e r f l o w − 1 since the function is meant to recieve as argument the overflow value and not the terminal count. has shown in th...
外部时钟模式 2:外部触发输入 ETR (External TRigger),计数器可在外部触发输入 ETR 出现上升沿或下降沿时计数。 内部触发输入(ITRx,Internal TRigger(x=0,1,2,3))(编码器模式):使用一个定时器作为另一个定时器的预分频器,如可以配置一个定时器Timer1作为另一个定时器Timer2的预分频器。 如上图,TIM1、TIM...
(7) TIM_ARRPerloadConfig()来设置是否使用预装载缓冲器 (8)TIM_ITConfig()来开启TIMx的中断 其中(3)-(6)步骤中的参数由TIM_TimerBaseInitTypeDef结构体给出。 步骤(3)中的预分频系数用来确定TIMx所使用的时钟频率,具体计算方法为:CK_INT/(TIM_Perscaler+1)。CK_INT是内部时钟源的频率,是根据2.1中所描述...
1)16bit定时器 2)32bit定时器(TIM2、TIM5) 3)24bit定时器(Systick) 二、三种定时器(高级&通用&基本)区别 对于STM32F4XX,三种定时器(高级、通用、基本)的区别如下表 根据以上表格,可以看出 1)高级定时器(TIM1&TIM8)是16bit,支持向上、向下、向上/向下计数模式,可以产生DMA请求,捕获/比较通道有4个,支持...
It is useful to start several timers at the same time or to control a window in which a slave timer is enable. The Counter Enable signal is generated by a logic OR between CEN control bit and the trigger input when configured in gated mode. ...
TIMER_cfg(); //开启定时器2 TIM_Cmd(TIM2,ENABLE); while(1); } void RCC_cfg() { //定义错误状态变量 ErrorStatus HSEStartUpStatus; //将RCC寄存器重新设置为默认值 RCC_DeInit(); //打开外部高速时钟晶振 RCC_HSEConfig(RCC_HSE_ON);
打开CubeMX,创建一个新的工程,在SystemCore和Timer就能看到这个单片机的几乎所有可以使用的定时器资源: 此图是STM32F103C8T6的定时器资源 我们能看到有RTC以及TIM1~TIM4的定时器资源。其中RTC指的是实时时钟,TIM1~TIM4是定时器。对于M3架构STM32有如下的定时器划分我们可以在参考手册中查到: ...
1、timer.c文件 #include "STM32Lib\\stm32f10x.h" void TIM2_Configuration(void) { TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure; TIM_OCInitTypeDef TIM_OCInitStructure; u16 CCR1_Val = 4000; u16 CCR2_Val = 2000; u16 CCR3_Val = 1000; ...
1. STM32的Timer简介 STM32中一共有11个定时器,其中2个高级控制定时器,4个普通定时器和2个基本定时器,以及2个看门狗定时器和1个系统嘀嗒定时器。其中系统嘀嗒定时器是前文中所描述的SysTick,看门狗定时器以后再详细研究。今天主要是研究剩下的8个定时器。