Y. Zhao: ‘Elastic modulus of 316 stainless-steel lattice structure fabricated via binder jetting process', Mater. Sci. Technol. , 2016 .Y. Tang, Y. Zhou, T. Hoff, M. Garon, Y.F. Zhao, Elastic modulus of 316 stainless steel lattice structure fabricated via binder jetting process, Mater...
Young’s modulus 189 – 210 GPa Yield strength (elastic limit) 170 – 1,000 MPa Tensile strength 480 – 2,240 MPa Elongation 5 – 70 % Hardness—Vickers 130 – 570 HV Fatigue strength at 107 cycles 175 – 753 MPa Fracture toughness 62 – 150 MPa·m1/2 Thermal properties Melting point...
Elastic (Young's, Tensile) Modulus 200 GPa 28 x 106 psi Elongation at Break 25 % Fatigue Strength 180 MPa 26 x 103 psi Poisson's Ratio 0.28 Shear Modulus 77 GPa 11 x 106 psi Shear Strength 330 MPa 48 x 103 psi Tensile Strength: Ultimate (UTS) 510 MPa 74 x 103 psi Tensile Strengt...
Annealed (+A) 1.4122 Stainless SteelQuenched and Tempered (+QT750) 1.4122 Stainless SteelMechanical Properties Elastic (Young's, Tensile) Modulus 200 GPa 29 x 106 psi Elongation at Break 14 % Fatigue Strength 260 to 360 MPa 38 to 52 x 103 psi Poisson's Ratio 0.28 Shear Modulus 77 GPa ...
Table 3. Typical physical properties of 304-grade stainless steel in the annealed condition GradeDensity (kg/m3)Elastic Modulus (GPa)Mean Coefficient of Thermal Expansion (μm/m/°C)Thermal Conductivity (W/m.K)Specific Heat 0-100 °C (J/kg.K)Electrical Resistivity (nΩ.m) 0-100 °C0-...
Grade Density (kg/m3) Elastic Modulus (GPa) Mean Coefficient of Thermal Expansion (mm/m/°C) Thermal Conductivity (W/m.K) Specific Heat 0-100°C (J/kg.K) Electrical Resistivity (nW.m) 0-100°C 0-315°C 0-538°C at 100°C at 500°C 304/L/H 8000 193 17.2 17.8 18.4 16.2 21...
Grade Density (kg/m3) Elastic Modulus (GPa) Mean Coefficient of Thermal Expansion (mm/m/°C) Thermal Conductivity (W/m.K) Specific Heat 0-100°C (J/kg.K) Electrical Resistivity (nW.m) 0-100°C 0-315°C 0-538°C at 100°C at 500°C 304/L/H 8000 193 17.2 17.8 18.4 16.2 21...
The typical elastic modulus of stainless steels at room temperature (25°C) ranges from 190 to 210 GPa. The typical density of stainless steels ranges from 7.75 to 8.1 g/cm3. The typical tensile strength varies between 515 and 827 MPa. The wide range of ultimate tensile strength is largely...
GradeDensity (kg/m3)Elastic Modulus (GPa)Mean Coefficient of Thermal Expansion (mm/m/°C)Thermal Conductivity (W/m.K)Specific Heat 0-100°C (J/kg.K)Electrical Resistivity (nW.m) 0-100°C0-315°C0-538°Cat 100°Cat 500°C ...
Porous stainless steel implants match very well with bone in terms of the elastic modulus. Powder metallurgical Cr-Mn-N stainless steel foams were developed after sintering at 1,100°C for 20 hours by using mechanically alloyed 18Cr-8Mn-0.9N powders [96]. A microstructural observation and dry...