一、解决方法: 1.只需在ST-Link Utility上点击Connect时,手动硬复位一下stm32单片机即可连接成功 2.有的型号不需要手动复位,有的型号需要。实测f103就不需要手动复位即可连接。这里进行一个配置,让需要复位的型号也不再需要复位:(高能,这个方法是我自己乱试出来的,网上也没找到过) (1) 如图2,点击Target->Settin...
“Can not connect to target! 解决办法,可用镊子把复位脚拉低,单击STM32 ST-LINK Utility连接按钮,松开镊子,就OK了!再把数据清除了。
-Set BOOT0 high and get the device to boot into System Loader mode and erase it. This still gave me the cannot connect to target error. -Full chip erase in STM32 ST-LINK Utility with reset output set (high and low). Again, the same error. One thing I am worried...
However, there are other issues that can cause the target connection problem. In my case, i was enable to connect the board under the normal connexion mode and therefore i cannot reprogram my cpu. Here is what I've done to solve that problem: I used ST-Link v2 and ST-Link Utility. ...
要设置一下中间的Programming algorithm 里选择你的MCU信息。_T-LINK是一个用于STM8和STM32微控制器系列的在线调试器和编程器，也是大家口中的下载器。junction link 接合链路，就是ARM板上要用的JLINK。_T-Link具有SWIM、JTAG / SWD等通信接口，用于与STM8或STM32微控制器进行通信（各版本有差异）。
使用utility连接也会报错,报错信息如下:Cannot connect to target 按照提示,在烧录时按Reset按键,成功烧录了软件。使用一行行注释排除的方法,最后定位在DS18B20_Init初始化函数这。程序使用了PB15作为了18B20的输入,这个口也是JTAG的接口,在使用时,不能按照常规GPIO口进行配置。使用时,需要先禁止JTAG,然后使能SWD。如果...
解决ST-LinkUtility出现Can not connect to target!的问题 ST-LinkUtility需要配套ST-Link烧录器才能使用,是针对ST家单片机的量产烧录工具软件。 2023-05-25 15:26:58 ST-Link无法烧录怎么解决 问题描述:参加STM32峰会创客秀比赛,进入复赛后拿到STM32H747-Discovery Kit的板子,先去做了ST-Link的升级,谁知道直接升...
ST-LINK utility. When working with the STM32 ST-LINK utility, it is recommended to download the ST-LINK in- circuit debugger/programmer for STM8 and STM32 microcontrollers User manual (UM0627) or the ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 User manual (UM1075), ...
10/54 UM0892 Rev 24 UM0892 2.2.4 Target menu STM32 ST-LINK utility user interface Figure 6. Target menu Connect Connects to the target device and displays the Device Type, Device ID and Flash memory size in the device information zone. Disconnect Disconnects from the target device. Erase ...
Target menu Figure 6: Target menu 6/22 DocID029716 Rev 2 UM2109 Target functions Connect Dis connect Erase chip Erase sectors Program Program and verify Blank check Compare device memorywith file MCU core Automatic mode Settings BlueNRG-1 ST-LINK Utility user interface Table 1: Target menu ...