RN0093 Release note Firmware upgrade for ST-LINK, ST-LINK/V2, ST-LINK/V2-1 and STLINK‑V3 boards About this release note This release note contains information about the latest firmware versions for ST-LINK, ST-LINK/V2, ST-LINK/V2-1, and STLINK-...
同样,出现“Upgrade successful”说明升级成功。 2.2 通过STM32 ST-LINK Utility升级 地址: st.com/en/development-t 使用过STM32 ST-LINK Utility的人,基本都知道ST-LINK菜单。通过下面子菜单Firmware update(如下图),即可进去升级界面。 STM32 ST-LINK Utility是基于Windows平台的一个编程软件,通过上述方式进入...
Old ST-LINK firmware version. Upgrade ST-LINK firmware STEP1:找到 STM32CubeIDE 安装路径,确定待替换 exe 路径 也可以直接使用 everything 之类的搜索软件,快速地位下面两个 exe 的路径 STM32_Programmer_CLI.exe 一般位于STM32CubeIDE_1.0.0\STM32CubeIDE\plugins\com.st.stm32cube.ide.mcu.externaltools....
b. 插上stlink c. 不要点其他的,直接点击ST-LINK->Firmware update,弹出如下框。 点击Device connect即可弹出如下部分: 点击yes即可升级成功。
Ok, I saw an option "Firmware upgrade" option inside ST-LINK. So I tried to use this option. I disconnected ST-LIINK and clicked on this link. And I got: When I made a connection, then this link was dimmed. So I have a question: Is it possible to upgrade ST-LINK firmware? Such...
一段时间没有使用st-link烧写程序了。打开keil5准备把程序烧写到stm32板子上时,报错Old ST-LINK firmware detected.do you want to upgrade it?经查,发现是stlink固件太旧了,需要升级。升级就升级吧,结果点击之后没反应。于是上网搜解决方案。原来就是到stm32官网下载st-link utility。于是登录官网下载。
Failed to firmware upgrade ST-LINK firmware on STM32MP157F-DK2 board using STM32CubeProgrammer version 2.12 Go to solution SThon.1 Associate II 2023-03-29 06:04 AM Hi, I am using STM32CubeProgrammer version 2.12 running on Windows 10 to connect to the STM32MP157F-DK2 board ...
同样,出现“Upgrade successful”说明升级成功。 2.2 通过STM32 ST-LINK Utility升级 地址: https://www.st.com/en/development-tools/stsw-link004.html 使用过STM32 ST-LINK Utility的人,基本都知道ST-LINK菜单。通过下面子菜单Firmware update(如下图),即可进去升级界面。
Upgrade refer to the following tutorial: The firmware version on hand is: STLinkV2.J16.S4; after programming the firmware, it is found that the STM32 ST-LINK Utility can be used to connect to the chip to be programmed, but if you try to simulate it with MDK, it will not succeed. ...
官网固件升级: 从st.com/en/development-...下载，V2版本如V1J13S4、V2J33S7等。Windows平台直接运行工具，连接设备并进行升级，成功后显示“Upgrade is successful”。STM32 ST-LINK Utility: 通过菜单Firmware update进行升级，但内置固件可能不是最新版本。STM32CubeProg: 集成了全平台升级工具，同样...