There are several ways to recognise a clone: you could, for example, open your ST-LINK/V2 (one screw is under the sticker on the back between the logo and the edge, another one is roughly where you have the word "SWIM") and you would then find a fake STM32F103. If you don't wan...
ST-LINKV2在MDK环境下,使用SW-DP模式下载hex时出现以下错误提示:出现这种错误一般都是ST-LINK和目标板SW-DP接线时没有将目标板的电源线接到ST-LINK插座的TVCC端导致的。解决步骤: 1. 目标板使用外接电源供电,不要使用ST-LINK供电。2.ST-LINK和目标板SW-DP接线正确。3.MDK设置正确: 1)ST-LINK插座TVCC和目...
I have similar situation, stmf103re, st-link firmware v2j23s4, custom board, target detection fail, and voltage detection fail, connected only swdio, swclk, gnd, and vdd, nrst connected with pull-up (100k), vdd on st-link is connected to pin 1 (tryed also on pin 2).Conne...
STM32F103:一.(2)STLINK的配置 STLINK的配置 1.安装STLINK驱动 选择相应位数进行安装 安装完成页面 设备管理器处显示STLINK 2.设置STLINK 勾选USE STLINK 按照如图进行设置 最后,选中 Reset and Run 选项,以实现在编程后自动运行,其他默认设置即可。 选择芯片型号容量 这样正常情况下就能进行STLINK下载 3.STLINK...
Connecting the PC and STM8/STM32 application board through ST-LINK/V2 to establish hardware connection: Supported Devices Microcontrollers supported by STVP release 3.2.8: Product lineMicrocontroller STM32 STM32F100xx, STM32F101xx, STM32F102xx, STM32F103xx, STM32F105xx, STM32F107xx, STM32F2xxx,...
On other ST-LINK/V2-1 boards, refer to the schematics of the board to find how to reset the STM32F103CB microcontroller (solder bridge on the STM_RST signal). Summary of changes in ST-LinkUpgrade.exe 2.3.28 and STLinkUpgrade.jar 3.0.7 • On ST-L...
a)烧录固件 >> JFlash烧录教程 J-flash 的简易使用教程_开水烫白菜的博客-CSDN博客 >> JFlash工程:见附件,名为JFlash-STM32F103CBT6.jflash 使用JLink下的JFlash工具打开附件工程即可烧录,烧录完成可在keil中验证 !!!注意:不要使用Kei更新固件,本人在keil更新固件后始终出现STLink Connection Error或者No Target ...
STLINK V2 Application Computer Description Report Item Specifications: Dissipation Power: STM32F103C8T6 / STM32F103C6T6 Operating Temperature: STM32F401 STM32F411 STM32F4 is_customized: Yes Supported Debugging Interfaces: SWD, SWIM Compatible Compilers: IAR, STVD, STVP, KEIL, RVMDK Additional Features...
stlink utility 显示已经连接到板子，但是在keil start debugging 总是弹出来stlink connection error的...
1.检查ST-link V2灯是否为蓝色1秒闪一次:ST-linkV2重新插拔一次 2.驱动未成功安装:打开设备管理器>通用串行设备总线>看是否有STMicroelectronics STLink dongle 如果没有请重新安装驱动 3.更新硬件:开始>所有程序>ST Toolset>Setup>Upgrade STLink打开STLink-upgrade 点击Device connect>Yes 4.如果上一步连接失败:...