(2)下面两种方法之间的spi1-spi3如何连接? a. spi1 MISO <-> spi3 MISO / spi1 MOSI <-> spi3 MOSI / spi1 SCK<-> spi3 SCK / spi1 CS0 <-> spi CS0 b. spi1 MISO <-> spi3 MOSI / spi1 MOSI <-> spi3 MISO / spi1 SCK<-> spi3 SCK / spi1 CS0 <-> spi CS0 1 2 登...
读取芯片的状态字读出是0xff,说明工作不正常,动用逻辑分析仪监控spi总线的通信,意外的发现,sck信号和cs信号正常,但是mosi无信号输出,开始觉得可能是spi总线适配器有问题,后来仔细观察原理图之后,发现dataflash和mmc/sd是使用同样的io口的,即pa0,pa1,pa2,而我的内核配置中打开了对mmc的支持,所以导致mosi不正常,所以...
CS0 --- Pin 24 GPIO 8 (SPI0 CE0) SCK --- Pin 23 GPIO 11 (SPI0 SCLK) MOSI -- Pin 19 GPIO 10 (SPI0 MOSI) MISO -- Pin 21 GPIO 9 (SPI0 MISO) GND --- Pin 6 GND 5V --- Pin 1 5V /boot/config.txt: dtoverlay=mcp2515-can0,oscillator=16000000,interrupt=23 dtoverlay=mcp2515...
Serial.println("Setting VSPI_SCK"): Code: main.cppSelect all #include <Arduino.h> #include <SPI.h> #define VSPI_SCK 19 #define VSPI_MISO 21 #define VSPI_MOSI 20 #define VSPI_SS 18 void setup() { Serial.begin(115200);
在uboot 中也有显示和屏驱动,目的是显示logo。 • 板级dts 配置仓库。目的是通过board.dts 来配置一些通用的LCD 配置参数。对于linux4.9,该配置同时对内核及uboot 生效,对于linux-5.4,请参照下条。 • 对于linux5.4,还需额外配置uboot 专用板级dts 配置仓库。 确保全志显示框架的内核配置有使能,查看menuconfig...
• PA5的复用功能里有SPI1_SCK然后PB3也有这个功能,现在PA5烧掉能不能用PB3替代? 3093 • STM32的PB0-15接收并行16位AD输出出现错误 3056 • 使用STM32F103 PB3外部中断不正常,无法触发是为什么? 1921 • stm32点灯不亮找不到原因,请问问题在哪? 17442 • 用RT_OTA生成Boot烧写进入失败是何...
We now need to create a boot loader application to copy the S-records into their correct memory locations. SDK provides a boot loader template which is used for parallel NOR Flash memory. We will use a modified version of the boot loader template to read from SPI Flash using the Xilinx ...
Device latches addresses, commands, and program data in SI on SI / IO0 the rising-edge of SCK. SI must not be driven during x2 or x4 READ operation. Serial Data Output (Output) / IO1 (Input/Output) SO / IO1 SO transfers data serially out of the device on the falling-edge of ...
SEL. One SPI device acts as a master device which controls the data flow using the SEL and SCK signals to indicate the start of data communication and the data sampling rate. To receive a data byte, the streamed data bits are latched on a specific clock edge and stored in the data reg...
在uboot 中也有显示和屏驱动,目的是显示logo。 • 板级dts 配置仓库。目的是通过board.dts 来配置一些通用的LCD 配置参数。对于linux4.9,该配置同时对内核及uboot 生效,对于linux-5.4,请参照下条。 • 对于linux5.4,还需额外配置uboot 专用板级dts 配置仓库。