RDID(Read Identification :读ID):发送命令RDID(9F),然后接收第1个字节的memory type(20H),第二个字节的memory capacity(15H)。后续的字节暂不关心。 WREN(Write Enable :写使能):在任何写或者擦除的命令之前,都必须首先打开写使能。打开写使能为发送命令WREN(06h)。 RDSR(Read Status Register:读状态寄存器)...
RTL netlist如下: 板子的上的晶振为25MHz,通过PLL IP产生100MHz,供其他模块使用。flash_read_status_register模块的功能是发送8’h9F指令,然后读取Manufacturer ID, Memory Type, Capacity共三个字节的信息。SPI_Master模块是SPI驱动模块,USRMCLK为Lattice提供的宏,用于解决SPI专用端口的时钟SCK信号的问题。可以看到顶层...
RDID(Read Identification :读ID):发送命令RDID(9F),然后接收第1个字节的memory type(20H),第二个字节的memory capacity(15H)。后续的字节暂不关心。 WREN(Write Enable :写使能):在任何写或者擦除的命令之前,都必须首先打开写使能。打开写使能为发送命令WREN(06h)。 RDSR(Read Status Register:读状态寄存器)...
RDID(Read Identification :读ID):发送命令RDID(9F),然后接收第1个字节的memory type(20H),第二个字节的memory capacity(15H)。后续的字节暂不关心。 WREN(WriteEnable :写使能):在任何写或者擦除的命令之前,都必须首先打开写使能。打开写使能为发送命令WREN(06h)。 RDSR(Read Status Register:读状态寄存器):...
RDID(Read Identification :读ID):发送命令RDID(9F),然后接收第1个字节的memory type(20H),第二个字节的memory capacity(15H)。后续的字节暂不关心。 WREN(Write Enable :写使能):在任何写或者擦除的命令之前,都必须首先打开写使能。打开写使能为发送命令WREN(06h)。
2. CYCLE TYPE + TYPE:该字段由HOST驱动,对Cycle的事务类型(Memory、I/O、DMA)以及传输方向进行说明;LAD[0]在该状态中被保留,外设需忽略该bit;具体定义如下表格所示; 3. ADDR:对于I/O操作是4个clock位宽(16bit,64KB地址空间),对于Memory操作时8个clock位宽(32bit,4GB地址空间),地址并不会在DMA操作中输出(...
(Program + Verify)Memory size W25X80VSSIG 8Mb 11sW25Q16VSSIG 16Mb 15sW25Q32VSSIG 32Mb 20.5sW25Q64FVSSIG 64Mb 48.5sW25Q128BVFIG 128Mb 94sW25Q256FVFIG 256Mb 157sS25FL512SAGMFI011 512Mb 297s*Please note the programming and verify time will depend on different IC type; please refer to...
29 * - memory packing (12 bit samples into low bits, others zeroed) 30 * - priority 31 * - drop chipselect after each word 32 * - chipselect delays 33 * - ... 34 */ 35 } 1.1 spi设备的添加spi_new_device 1 struct spi_device *spi_new_device(struct spi_master *master, ...
(&pdev->dev, "No memory for spi_master\n"); err = -ENOMEM; goto err_nomem; } /* 获取spi的私有数据结构体并初始化为空 */ hw = spi_master_get_devdata(master); memset(hw, 0, sizeof(struct s3c24xx_spi)); /* 设置spi的私有数据*/ hw->master = spi_master_get(master); hw->...
pr_err("Failed to request memory \r\n"); return-ENOMEM; } /* 1、创建设备号 */ /* 采用动态分配的方式,获取设备编号,次设备号为0 */ /* 设备名称为 SPI_NAME,可通过命令 cat /proc/devices 查看 */ /* RC522_CNT 为1,只申请一个设备编号 */ ...