在spi_ioc_transfer结构体中设置以下字段: tx_buf:指向发送数据缓冲区的指针。 rx_buf:指向接收数据缓冲区的指针。 len:要传输的数据长度。 delay_usecs:传输之间的延迟时间(以微秒为单位)。 speed_hz:SPI时钟速度(以赫兹为单位)。 bits_per_word:每个字的位数。 根据变量mode的值设置tr结构体中的tx_nbits和r...
__u8 tx_nbits; __u8 rx_nbits; __u8 word_delay_usecs; __u8 pad; /* If the contents of 'struct spi_ioc_transfer' ever change * incompatibly, then the ioctl number (currently 0) must change; * ioctls with constant size fields get a bit more in the way of * error checking than...
它使用`ioctl`系统调用和`SPI_IOC_MESSAGE`命令来执行SPI数据传输。 第四部分:`main`函数是程序的入口点。它将`send_num`变量设置为38,然后调用`func_set_opt`来配置SPI设备。接着,它调用`func_transfer`来发送和接收数据,并使用预定义的`transfer_tx`和`transfer_rx`缓冲区。最后,它打印接收到的数据长度,并...
structspi_ioc_transfer{__u64tx_buf;//发送数据缓存__u64rx_buf;//接收数据缓存__u32len;//数据长度__u32speed_hz;//通讯速率__u16delay_usecs;//两个spi_ioc_transfer之间的延时,微秒__u8bits_per_word;//数据长度__u8cs_change;//取消选中片选__u8tx_nbits;//单次数据宽度(多数据线模式)__u8...
ioctl(fd, SPI_IOC_RD_MAX_SPEED_HZ, &speed); ioctl(fd, SPI_IOC_WR_MAX_SPEED_HZ, &speed); 复杂的数据通信: cmd:SPI_IOC_MESSAGE arg:struct spi_ioc_transfer struct spi_ioc_transfer { __u64 tx_buf; __u64 rx_buf; __u32 len; ...
struct spi_transfer *k_xfers; struct spi_transfer *k_tmp; struct spi_ioc_transfer *u_tmp; unsigned n, total, tx_total, rx_total; u8 *tx_buf, *rx_buf; int status = -EFAULT; spi_message_init(&msg); k_xfers = kcalloc(n_xfers, sizeof(*k_tmp), GFP_KERNEL); ...
qn15580637532019-07-18 10:04:12
TR.TX_nbits = 0; TR.Rx_nbits = 0; tr.word_delay_usecs = 0; TR.PAD = 0; int FD_SPI = open ("/dev/spidev0.0"、O_RDWR | O_NOCTTY); int tmp = ioctl (FD_SPI、SPI_IOC_MESSAGE (1)、&tr); 如果(tmp < 0) { //错误处理 ...
transfer_f转 义字符串(fd、input_tx); 否则、如果(input_file) transfer_file (fd、input_file); 如果(transfer_size){ struct timespec last_stat; Clock_gettime (clock_monotonic、&last_stat); while (iterations->0){ struct timespec current; ...
tx_nbits = 1, .rx_nbits = 1 }; ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr); if (ret < 1) printf("can't send spi message\n"); } void spi_init(int fd) { int ret = 0; // spi mode 设置SPI 工作模式 ret = ioctl(fd, SPI_IOC_WR_MODE32, &mode); if (ret == -1) ...