其余保持不变。 此外将clock IP核的时钟输出2输出的100MHz,连接到AXI_Quad SPI软核的外部时钟输入引脚上,此时AXI_Quad SPI软核与FLASH的工作时钟是100MHz/Frequency Ratio = 50MHz。 GPIO IP核 添加2个GPIO核,修改ip核名称位axi_led、axi_key;一个用于LED输出,一个用于按键Key输出,分别修改IP核,设置位全输出...
如果设置为16,即每次数据传输宽度为16-bit,一次数据传输需要16个SCK时钟 Frequency Ratio 频率比是由两个数的乘积。输出的SPI时钟(sck)满足: sck=ext\_spi\_clk/Fre\_Ratio Enable Master Mode 这个选项决定SPI设备的主从模式,也可以在配置寄存器60h中修改。 Enable STARTUPEn Primitive STARTUPEn 原语有⼀个...
spi.c: 一方面对SPI子系统进行初始化工作,注册spi bus,注册spi_masterclass,同时提供spi设备驱动对spi总线进行操作的API。 另一方面SPI子系统对spi控制器层,提供注册控制器的api和回调操作函数。spi.h包含了spi核心层的一些重要数据结构,structspi_master;structspi_transfer;structspi_message,以及一些实现比较简单的函...
拷贝一份我们之前的 Keil 工程模板05_Template, 然后将工程文件夹重命名为“SPI_OLED”,并进入该文件夹里面双击 Keil 工程文件,打开该工程。 工程新建好之后,在工程根目录的 “src” 文件夹下面新建 “spi_oled” 文件夹, 再进入 “spi_oled” 文件夹里面新建源文件和头文件:“bsp_spi_oled.c” 和“bsp_sp...
另外一种是使用 fbtft 进行 SPI 屏幕驱动。 fbdev 方式由于 pinctrl 在新内核中调用方式出现修改,所以暂时无法使用。修改难度较大。 fbtft 虽然官方wiki表明不建议在 Linux 5.4 中使用,但是其实也是可以使用的,只需要修改一下 GPIO 的注册方式就行。 一、环境搭建# ...
Ensure that the correct values are used when deciding on the AXI clock and selecting the Frequency Ratio parameter. The AXI clock and the Frequency Ratio parameter determine the clock frequency at the SCK pin of the core. While using different external SPI slave devices, the Frequency Ratio ...
(0xd5); //--set display clock divide ratio/oscillator frequency spi_oled_send_commend(0x80); //--set divide ratio, Set Clock as 100 Frames/Sec spi_oled_send_commend(0xd9); //--set pre-charge period spi_oled_send_commend(0xf1); //Set Pre-Charge as 15 Clocks & Discharge as 1...
0xAE, // Display OFF 0xD5, 0x80, // Set display clock divide ratio/oscillator frequency ...
SPI_Write_Byte(0xd5,OLED_CMD);//--set display clock divide ratio/oscillator frequency SPI_Write_Byte(0x80,OLED_CMD);//--set divide ratio, Set Clock as 100 Frames/Sec SPI_Write_Byte(0xD9,OLED_CMD);//--set pre-charge period
A summary of the frequency ratio restrictions between the bit-rate clock (sclk_out / sclk_in) and the SPI peripheral clock (spi_clk) are described as, When SPI Controller works as master, the F spi_clk >= 2 × (maximum F sclk_out ) ...