此时主装置便透过Slave select(chip select)来选择欲沟通的从装置。依照不同的应用环境SPI汇流排可操作在四线式状态下(SCLK、MOSI、MISO、SS),这个时候SPI可拥有全双工能力。在三线式状态下(SCLK、DATA、SS)则是半双工方式,若连接环境较为单纯时,则可衍生出两线式状态(SCLK、DATA),此时SPI总线上仅只有一个主...
This resource implements Serial Peripheral Interface (SPI) chip select pins (CSN) for theSPI Data Transferresource. Multiple chip select pins can be used to access multiple SPI slaves, with shared clock and data lines for all slaves. The pins are mapped in theI/O Mapping Panel. The ...
SS/CS (Slave Select/Chip Select) – 片选信号。 SPI协议特点 实际上,从机的数量受系统负载电容的限制,它会降低主机在电压电平之间准确切换的能力。 时钟信号 每个时钟周期传输一位数据,因此数据传输的速度取决于时钟信号的频率。 时钟信号由于是主机配置生成的,因此SPI通信始终由主机启动。 设备共享时钟信号的任何...
.chip_select = 0, //片选线号,在S5PC100的控制器驱动中没有使用它作为片选的依据,而是选择了下文controller_data里的方法。 9. .controller_data = &smdk_spi0_csi[0], 10. }, 11. }; 12. [] = { 13. [0] = { 14. .set_level = smdk_m25p10_cs_set_level, 15. .fb_delay = 0x3, ...
//SPI 设备structspi_device{structdevicedev;structspi_master*master;//指向SPI控制器u32 max_speed_hz;//最大速率u8 chip_select;//片选u8 mode;//SPI设备模式,使用下面的宏#defineSPI_CPHA 0x01/* clock phase */#defineSPI_CPOL 0x02/* clock polarity */#defineSPI_MODE_0 (0|0)/* (original ...
chip_select: spi总选用于区分不同SPI设备的一个标号,不要误以为他是SPI设备的片选引脚。指定片选引脚的成员在下面 bits_per_word: 指定SPI通信时一个字节多少位,也就是传输单位 mode: SPI工作模式,工作模式如以上代码中的宏定义。包括时钟极性、位宽等等,这些宏定义可以使用或运算“|”进行组合,这些宏定义在SPI...
flash chip select */ CC2640R2_LAUNCHXL_UART_RX | PIN_INPUT_EN | PIN_PULLDOWN...
2. No pullup resistors required 3. Full-duplex operation 4. Noise immunity1. Larger number of bus line connections 2. Individual chip-select lines required to communicate with more than one slave at a time 3. No acknowledgment of received data2-Wire: I²C and SMBus1. Fewer bus line ...
< Deselect the FLASH: Chip Select high*/GPIO_SetBits( GPIOA, GPIO_Pin_4 );/*!< SPI configuration*/SPI_InitStructure.SPI_Direction= SPI_Direction_2Lines_FullDuplex;/*双线双向全双工*/SPI_InitStructure.SPI_Mode= SPI_Mode_Master;/*主 SPI*/SPI_InitStructure.SPI_DataSize= SPI_DataSize_8b;/*...
< Deselect the FLASH: Chip Select high*/GPIO_SetBits( GPIOA, GPIO_Pin_4 );/*!< SPI configuration*/SPI_InitStructure.SPI_Direction= SPI_Direction_2Lines_FullDuplex;/*双线双向全双工*/SPI_InitStructure.SPI_Mode= SPI_Mode_Master;/*主 SPI*/SPI_InitStructure.SPI_DataSize= SPI_DataSize_8b;/*...