SPD Flash Tool是适用于用于展讯芯片组手机或平板设备固件的刷新工具。目前有三款不同的下载工具,适用于不同的使用场景。 FactoryDownload (用于PCBA阶段生产下载。该工具会初始化PhaseCheck、ProdNV分区、擦除NV参数、预写SN号) UpgradeDownload (用于PCBA或者手机整机的软件升级,升级前会检查校准标志位是否置pass,否则...
更改DDR2内存条SPD信息thaiphoon burner教程 首先读取50h的内存信息,也就是原厂的那一条,待内存SPD信息读取完毕后,选择FILE--Save Dump as,输入保存的文件名,我们就可以将其另存为一个以“THP”为后缀的文件了(一会要将这个信息刷入JS送的那条中)。然后再读取51h的那一条(这一步很重要呀,一定要先保存原来...
到“华军软件园”下载内存SPD信息修改软件Thaiphoon。解压后运行，进入“Thaiphoon主界面，单击“EEPROM”菜单，菜单底部会出现两条内存的SPD选项，比如“Read SPD at 50h”和“Read SPD at 52h”，分别对应主板“DIMM 1”和“DIMM 3”内存插槽。分别读取50h和52h的内存信息，单击“FILE”→“Save Dump...
The ROM dump file will be saved in the current directory with the namedimm81.spd. Be sure to verify the integrity of the dump: The CRC values in the ROM must all match their respective computed values. If they don’t, this means the ROM is damaged: either due to previous illegal writ...
(42V for load dump) and supports stop/sleep mode for power saving. It integrates two 5V LDOs for internal power system and external sensor, and also integrates 3.3V and 1.2V LDOs for MCU operation. It supports 5V I/O for logic and 3.3V I/O for analog input channel. The junction ...
I attached the SPDtool dump of the ram, hopefully maybe someone might find it of use if no one can help. I cant oc beyond 5ghz on the i7 950, but now i can see the door open if i can only sort this out. Really appreciate any kind of help. Quick edit ICH10R is support...
I could take a attempt ,but i can't guarantee 100% successfully remove the spd write restriction. If you want to try ,please make a bios dump with this tool then attach the file. (Run dump.bat as administrator.) Contact me. My bios unlock page. Donate me Posts...
。 在读取过程中有进度条指示(图五),读取的过程几秒钟就可以完成了,图六就是读取的我的电脑上的Kingma某256MDDR400内存条的SPD信息。 这时你可以用Tool菜单下的ViewDetail查看内存的详细信息(图六),查看完毕可以用ViewDump(或按工具栏上的Dump按钮)回到读出时的状态。©...
1) 3.3V 是否正常: ©2022 旋智科技(深圳)有限公司 21 of 50 RC-109- SPD1148 低压吸尘器调试指南 A/0 万用表量测 VDD,应该量到 3.3V 左右 2) 1.2V 是否正常: 万用表量测 VDD12,应该量到 3.3V 左右 3) 连接 SWD 接口到 Jlink 等调试器,打开 Keil-->Flash-->Configure Flash Tool,检查 是否...
Would you please add printf sentence after the following section in the function __get_spd to dump SPD information read by u-boot? i2c_write(SPD_SPA0_ADDRESS, 0, 1, &dummy, 1); ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, 256); if (!ret) { i2c_write(SPD_SPA1_...