spanning-tree mst configuration instance 0 vlan 1-99, 101-199, 201-4094 instance 10 vlan 100 instance 20 vlan 200 以下说法正确的是 A. vlan 100的根网桥是SW2 , vlan200的根网桥是SW3 B. vlan 100的根网桥是SW3,vlan 200 的根网桥是SW2 C. 以上说法都不对 ...
SW1(config)#spanning-tree mode mst --修改成MST模式 SW1(config)#spanning-tree mst configuration SW1(config-mst)#name CCIE SW1(config-mst)#instance 1 vlan 1 SW1(config-mst)#instance 2 vlan 10 SW1#show spanning-tree mst configuration Name [CCIE] Revision 0 Instances configured 3 Instance ...
对于RSTP（802.1W），思科采用per-vlan RSTP配置，简化了VLAN特定的RSTP配置。同样，MSTP（802.1S）允许基于VLAN实例的生成树配置，通过Switch(config)#spanning-tree mode mst命令启用MSTP模式，并通过Switch(config)#spanning-tree mst configuration命令进入MST配置模式。这些命令和特性旨在确保网络的稳定性...
spanning-tree mst configurationname BACKBONErevision 1! spanning-tree mst 0-1,8 priority 4096 spanning-tree vlan 11,101-102,104,106 priority 4096 The switch doesn't have trunk set up with anything and the only vlan on switch is vlan 11; I think can replace all the config above with: ...
51CTO博客已为您找到关于spanning-tree mst configuration的相关内容,包含IT学习相关文档代码介绍、相关教程视频课程,以及spanning-tree mst configuration问答内容。更多spanning-tree mst configuration相关解答可以来51CTO博客参与分享和学习,帮助广大IT技术人实现成长和
SW1(config)#spanning-tree mst configuration //进入 MSTP 配置模式 SW1(config-mst)#name CCIE //设置域名 SW1(config-mst)#revision 1 //设置修订级别,默认是 0, SW1(config-mst)#instance 1000 vlan 1-5 //进程创建范围 0-4094, 1-5关联进程 1000 ...
Refer to the show spanning-tree mst configuration output shown in the exhibit. What should be changed in the configuration of the switch SW_2 in order for it to participate in the same MST region? () SW...
spanning-tree mst hello-time Command Objective This command configures the spanning tree hello time. The no form of this command resets the hello time to its default value. The hello time represents the time interval (in seconds) between two successive configuration BPDUs genera...
The Internal Spanning Tree (IST), which is a special MST instance with an instance ID 0. By default, all the VLANs are mapped to IST.CSTThe Common Spanning Tree (CST), that is the spanning tree connecting all MST regions. As is shown in Figure 1-3, region1-region 4 are connected ...
active region-configuration 默认情况下在启用STP之后,H3C交换机使用的是MSTP。因此不需要执行stp mode mstp。 配置之后在Cisco交换机上执行show spanning-tree mst可以看到连接H3C的交换机的端口状态由p2p变为P2p Pre-STD-Rx。而且从H3C的网站上没有明确的文档说H3C的交换机支持MSTP的802.1d-2004标准,所以Cisco的交换...