spanning-tree bpdufilter enable 命令通常用于在支持STP(生成树协议,如RSTP、MSTP等)的网络设备上启用BPDU(桥接协议数据单元)过滤器。启用此功能后,网络设备将配置为过滤或忽略接收到的BPDU帧,BPDU帧是STP协议用于发现和维护网络无环拓扑的关键信息包。 2. 详述启用BPDU过滤器(BPDU Filter)的作用 启用BPDU过滤器的主...
BPDU是生成树协议(STP)和快速生成树协议(RSTP)中使用的数据包,用于在交换网络中选举根桥和避免环路。 在某些网络设备上,可以通过配置命令来启用BPDU过滤。例如,在Cisco设备上,可以使用以下命令: spanning-tree bpdufilter enable 这条命令会将BPDU过滤功能开启,使得交换机端口只转发非BPDU流量,从而阻止了STP协议的数据...
SW1(config)#spanning-tree portfast edge bpdufilter default 如果把SW1的E1/1配置为bpdufilter则该接口不会发送BPDU报文,则对端SW2 E1/1接口收不到任何BPDU报文从BLK状态变为转发FWD,此时就产生环路。---不建议使用 === Loopbuard: 在DP指定端口配置Loopbuard: SW1(config)#spanning-tree mode rapid-pvs ...
A:全局配置:如果在全局配置了BPDU Filter,那么接口放弃PortFast特性,转而进入正常的STP操作,转发BPDU。 B:接口配置:如果是在接口下明确配置BPDU Filter,那么交换机的这个接口将不发送任何BPDU,并且丢弃接收到的所有BPDU。 SW(config-if)#spanning-tree portfast SW(config-if)#spanning-tree bpdufilter enable | disa...
51CTO博客已为您找到关于spanning-tree bpdufilter enable的相关内容,包含IT学习相关文档代码介绍、相关教程视频课程,以及spanning-tree bpdufilter enable问答内容。更多spanning-tree bpdufilter enable相关解答可以来51CTO博客参与分享和学习,帮助广大IT技术人实现成长和
config interface ethernet config interface port-channel config interface mlag-port-channel History 3.1.0000 Example switch (config interface ethernet 1/1) # spanning-tree bpdufilter enable Related Commands show spanning-tree Notes This command can be used when the switch is connected to hostscl...
生成树协议(Spanning Tree Protocol,STP)是交换式以太网中的重要概念和技术,该协议的目的是在实现交换机之间的冗余连接的同时,避免网络环路的出现,实现网络的高可靠性。它通过在交换机之间传递桥接协议数据单元(Bridge Protocol Data Unit,BPDU)来互相告知诸如交换机的桥ID、链路性质、根桥(Root Bridge)ID等信息,以确...
生成树协议(Spanning Tree Protocol,STP)是交换式以太网中的重要概念和技术,该协议的目的是在实现交换机之间的冗余连接的同时,避免网络环路的出现,实现网络的高可靠性。它通过在交换机之间传递桥接协议数据单元(Bridge Protocol Data Unit,BPDU)来互相告知诸如交换机的桥ID、链路性质、根桥(Root Bridge)ID等信息,以确...
The spanning-tree bpdufilter command controls BPDU filtering on the configuration mode interface. BPDU filtering is disabled by default. Example These commands enable BPDU filtering on interface ethernet 5. switch(config)# interface ethernet 5 switch(config-if-Et5)# spanning-tree bpdufilter enable sw...
Interfaces connected to a single workstation or server should not receive bridge protocol data units (BPDUs). An interface with PortFast enabled goes through the normal cycle of spanning-tree status changes when the switch is restarted. You ...