使用命令搜索,我们按“S”键并开始输入Cut with Surface的前几个字符。选择合适的平面来平分模型,我们最终得到原始实体的一半,如下所示。 旋转面 要调整该面的拔模,我们将使用“移动面”的“旋转”设置,但这需要旋转轴,并且没有有用的直边限制该面。我们可以预先选择下面的这两个顶点,并添加Features > Reference ...
使用命令搜索,我们按“S”键并开始输入Cut with Surface的前几个字符。选择合适的平面来平分模型,我们最终得到原始实体的一半,如下所示。 旋转面 要调整该面的拔模,我们将使用“移动面”的“旋转”设置,但这需要旋转轴,并且没有有用的直边限制该面。我们可以预先选择下面的这两个顶点,并添加Features > Reference ...
使用命令搜索,我们按“S”键并开始输入Cut with Surface的前几个字符。选择合适的平面来平分模型,我们最终得到原始实体的一半,如下所示。 旋转面 要调整该面的拔模,我们将使用“移动面”的“旋转”设置,但这需要旋转轴,并且没有有用的直边限制该面。我们可以预先选择下面的这两个顶点,并添加Features > Reference ...
11.将上一步创建出来的拉伸曲面偏移20. 曲面偏移可以在“插入(Insert)”-“曲面(Surface)”-“偏移(Offset)”下调出。 12.用第11步创建出来的曲面做面切除。 面切除工具可以在“插入(Insert)”-“切除(Cut)”-“用曲面(With Surface)”下调出。 13.创建一个基准面,使之经过勺子上的一条边,并与右视基准面...
With multibody parts, under Feature Scope, select one of the following: All bodies. The surface cuts all bodies every time the feature rebuilds. If you add new bodies to the model that precede the cut feature in the FeatureManager design tree and that are intersected by the cutting ...
创建用面切除的位置在“插入(Insert)”-“切除(Cut)”-“用面(With Surface)”下可以调出。 也可以直接在快捷图标中调出。 单击左边的黑白色箭头标志可以切换切除的正反方向。 16.选择下图中所示的面作为草绘基准面。 17.用转换实体边将16条变线全部选上。然后单击右上角的草绘图标完成草绘。 转换实体边的位置...
Surface editing Tools 9-13 Delete Face 9-13 Replace Face 9-14 Delete Hole 9-15 Extend Surface 9-16 Trim Surface 9-16 Untrim Surface 9-17 Knit Surface 9-17 Thicken 9-18 Thickened Cut 9-19 Cut with Surface 9-19 Practical 1 9-20 ...
The feature you select depends on your base model and the shape you want the cut to produce. Cutting tools on the Features toolbar include: Extruded Cut Boundary Cut Revolved Cut Thickened Cut Swept Cut Cut With Surface Lofted Cut You can also cut material using a solid sweep, where yo...
This could be resolved later with an equation based on the thickness of the model, but that’s too much work for a “quick” model. Step 21: Cut with Surface Cut with Surfaceis the next command. It trims away the two solid bodies that are much too large. ...
, create the cutting surface—it can have any shape and can even be a sketch. Then hitCut Partand decide in the Resulting Bodies panel which ones to keep. In case of requiring only one part to be retained, an alternative is theCut with Surfacecommand underInsert → Cut → With Surface...