3、改了根据自己的底板改了 dts之后,时不时的卡死。有时候修改个 无关的 dts(比如加一个不存在的 i2c cpt 触摸 节点竟然好了)。修改无关的 dts 时好时坏。4、把uart3整个 dts节点全部 屏蔽掉,竟然能正常 启动并且输出,好像一直用 earlyprink输出的。5、有时候死机日志 也不一定固定在哪一行,老是感觉 ...
board.dts 部分配置: disp init configuration disp_mode (0:screen0<screen0,fb0>) screenx_output_type (0:none; 1:lcd; 2:tv; 3:hdmi;5:vdpo) screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50) (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p...
24、_callbacksvirtualtaskpre_trans(refaxi_transtr);/实现回调方法if()begin/通过信号控制出现频率tr.cmd_delay=0;tr.data_delay=0;endendtaskendclass442利用回调(Callback)进行针对覆盖率的验证覆盖率度量指标是验证设计可信度的重要指标。VMM验证方法学采用覆盖率组(CoverGroup)来定义验证的需求,并可以自动的生成...
SOC报告 阿里云系统与组织控制(SOC)报告是独立的第三方审计师针对阿里云为客户提供的云服务进行检查验证而出具的独立审计报告。该报告向阿里云的客户及其审计师说明了阿里云的关键控制及控制目标以帮助客户更好地评估阿里云的内控机制并有效地管理其外包风险。我们的客户可以通过阿里云的SOC报告了解到以下信息: SOC 1报告 (...
根据我的观察,大部分信息和不带参数时显示一致,除了SR-IOV设备分配出的Virtual Function设备。如下示例:物理网卡PF(physical function )显示一直 ,但VF(virtual function )显示却不同。 lspci -D:显示PCI domain号,默认的不加参数命令并不显示该值。 lspci -n/-nn:显示设备的vendor厂商号和device设备号;显示厂商...
SPDIF0/SPDIF1,8通道3D音频解码和N/AN/A 码/接口DTSVirtualX及DTSVirtualX音频 音效处理、智能 PDM0/PDM1,VAD(语音MPEG-HAudio音解码 音频处理 频解码 活动检测) 支持除了支持常用的 H.265/H.264/AV1/VP9/AVS支持HEVC、VP9、支持HEVC、支持H.265、 ...
[ 1.621283] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000028 [ 1.630106] Mem abort info: [ 1.632900] ESR = 0x96000005 [ 1.636001] EC = 0x25: DABT (current EL), IL = 32 bits [ 1.641328] SET = 0, FnV = 0 [ 1.644381] EA = 0, S1PTW...
cmd U-Boot commands functions /common Misc architecture independent functions /configs Board default configuration files /disk Code for disk drive partition handling /doc Documentation (don't expect too much) /drivers Commonly used device drivers /dts Contains Makefile for building internal U-Boot ...
Arm* DS makes it easy to display MMU settings, allowing you to easily obtain virtual memory settings. The command is listed in the online help as shown below.Enter mmu memory-map in Commands or check it in the MMU/MPU window as shown below.7...
1. Linux kernel log level: During the boot stage, Linux kernel could configure different log levels on the bootargs in the device tree(k3-j721e-common-proc-board.dts if use TDA4VM). By adding the loglevel=8 parameter in the Linux kernel configure, where the value ranges from 0 (...