SNMP侦听端口可通过snmp-agent port命令配置。 用户修改SNMP模块的相关配置后,如果关闭SNMP Agent功能,这些配置将暂时不生效。执行display current-configuration命令不会显示这些命令,执行save命令,这些配置也不会保存到配置文件。开启SNMP Agent功能后,这些配置会自动立即生效,不需要重复配置。 2. 配置步骤 (1) 进入...
snmp-agent target-host trap address udp-domain { ip-address | ipv6 ipv6-address } [ udp-port port-number ] [ dscp dscp-value ] params securityname security-string [ v1 | v2c | v3 [ authentication | privacy ] ] 可选 如果要将Trap信息发送给NMS,该步骤为必选,并将ip-address指定为NMS的...
(可选)执行命令snmp-agent udp-portport-num,修改SNMP Agent与网管连接所使用的端口号。 缺省情况下,SNMP Agent与网管连接所使用的端口号为161。 为了提升设备的安全性,请执行snmp-agent udp-port命令修改SNMP Agent的端口号。修改SNMP Agent与网管连接所使用的端口号以后,通过网管管理设备时,网管端指定的端口号必须...
(可选)执行命令snmp-agent udp-port port-number修改SNMP Agent侦听的端口号。 如果不执行此步骤,会使用缺省端口号进行侦听。 执行命令snmp-agent sys-info version v2c,配置SNMP的协议版本。 使能SNMPv2c后,被管理设备将同时支持SNMPv2c和SNMPv3,能同时满足使用SNMPv2c和SNMPv3的网管对设备进行监控和管理。 配置...
# snmp-agent target-host trap address udp-domain 10.1.1.1 udp-port 161 params securityname uhm...
SNMP采用UDP协议在管理端和agent之间传输信息。 SNMP采用UDP 161端口接收和发送请求,162端口接收trap,执行SNMP的设备缺省都必须采用这些端口。SNMP消息全部通过UDP端口161接收,只有Trap信息采用UDP端口162。 1.5、Snmp版本 SNMP 目前共有 3 个版本,分别为 v1、v2 和 v3,说明如下: ...
snmp=newSnmp(newDefaultUdpTransportMapping()); snmp.listen(); }//初始化CommunityTargettarget =newCommunityTarget(); target.setCommunity(newOctetString("public")); target.setVersion(SnmpConstants.version2c); target.setAddress(newUdpAddress(intranetDeviceIp + "/" +snmpPort)); ...
[h3c] snmp-agent target-host trap address udp-domain 202.38.160.6 udp-port 5000 params securityname public 11.2.10 设置接口发送状态trap报文 当接口的状态改变时(例如,由up变为down),可以向trap目标主机发送trap报文。 请在接口视图下进行下列配置。
SNMP uses the default UDP port 161 for general SNMP messages and UDP port 162 for SNMP trap messages. If these ports are being used by another protocol or service, you can change the settings by modifying the local Services file on the agent. The Services file is located in \ % SystemRoo...
rocommunity sunrj123 default -V systemonly rocommunity6 sunrj123 default -V systemonly 那么这里就把共同体修改为sunrj123 了,重启snmp服务,通过命令观察一下: root@apig:/etc/snmp# snmpwalk -v 2c -c public localhost memTotalReal.0 Timeout: No Response from localhost ...