Command = Trap 1.1.1.1/3374 V3 Trap = linkup SNMP Version = V3 Community = managev3user Command = Trap 1.7.3 SNMP日志典型配置举例 1. 组网需求 ·NMS与Agent相连,NMS的IP地址为1.1.1.2/24,Agent的IP地址为1.1.1.1/24。 ·在Agent上配置SNMP日志功能,以便记录NMS对Agent进行的操作。
Command = Trap 1.8.3 SNMP日志典型配置举例 1. 组网需求 ·NMS与Agent相连,NMS的IP地址为1.1.1.2/24,Agent的IP地址为1.1.1.1/24。 ·在Agent上配置SNMP日志功能,以便记录NMS对Agent进行的操作。 2. 组网图 图1-6 配置SNMP日志组网图 3. 配置步骤 ...
cachefsstat Command cachefswssize Command cal Command calendar Command cancel Command canonls Command captoinfo Command capture Command cat Command catman Command cb Command cd Command cdc Command cdcheck Command cdeject Command cdmount Command cdpd daemon cdpctl Command cd...
To configure a remote user, specify the IP address for the remote SNMP agent of the device where the user resides. Also, before you configure remote users for a particular agent, configure the SNMP engine ID, using thesnmp-server engineID remotecommand. The remote...
This command configures both SNMP v1 and v2. To remove the specified community string, use thenoform of this command. Syntax snmp-server communitycommunity-string [ro|rw|su][ip-address | ipv6-address][maskmask|prefixprefix-length] [viewview-name][type{router|oob...
(y/n)y Command executed successfully. 添加USM用户,用户名为“user”,认证鉴权协议为“SHA256”,数据加密协议为“NONE”,用户级别为“read_only”。 admin:/>add snmp usm user_name=user authenticate_protocol=SHA256 private_protocol=NONE user_level=read_only CAUTION: You are about to create a non-...
-bash: snmpwalk: command not found 如果snmp配置过了,还出现-bash: snmpwalk: command not found; 你可以安装net-snmp 和net-snmp-utils试一下, yum -y install net-snmp net-snmp-utils 我的就是因为没有安装net-snmp-utils才导致以上错误。
再安装:net-snmp 、net-snmp-utils,否则 snmpwalk: command not found yum -y install net-snmp net-snmp-utils 2、安装成功状态检查: AI检测代码解析 ## 查看状态 sudoservicesnmpd status 如果是未激活状态可以用命令:service snmpdstart激活 ## 测试看看服务是否正常 ...
A community name has been configured using the snmp-agent community command. Example The actual command output varies according to the device. The command output here is only an example. # Display the configured community name. <HUAWEI> display snmp-agent community Community name: %#%#SW5+R]B...
Here is an example of thesnmptablecommand: %snmptable -mALL -v2c -cprivatesnmp_agent_Ip_addresssysORTableSNMP table: SNMPv2-MIB::sysORTablesysORIDsysORDescrsysORUpTimeIF-MIB::ifMIBThe MIB module to describe generic objects for network interface sub-layers.0:0:00:00.01SNMPv2-MIB::snmpMIBTh...