SINAMICS S List Manual (LH1), 07/2007 故障与报警 故障与报警列表 注意: 可以通过设定参数来改变故障和报警的默认属性。 参考资料:/1H1/ SINAMICS S120 调试手册 “诊断”章节 故障和报警的列表(见3.2章)提供了与消息/报告被标准化的属性相关的信息。如 果一个指定的消息/报告的属性改变了,那么列表里面相关...
You can ind a description of alarm 201330 in the SINAMICS S120/S150 List Manual under fault A01330. Synchronization of time and date Note Synchronization of time The SINAMICS drives have no real-time clock. The time of day and date of the SINAMICS clock are synchronized in a 10-second ...
– 在出现电网故障时提供短路电流(穿越电网故障,Fault Ride Through),满足并网 标准 – 利用频移算法主动进行孤岛电网识别 – 扩展式电压检测及频率检测,用于电网故障后的自动重启 – 可自定义的控制点曲线(电压-时间监控和频率-时间监控),用于在电网故障期间 根据当地并网指令(Grid Code )对电压和频率进行监控。
inputs(BI)forTMs),cancreatetheparametersettingsarenotoverwritten.Thereasonforthisisthatadaptintheexpertlist. settings,whicharedifferentthansomemacroswritetomoreparametersthanothers. thosedescribedinthe ation. SINAMICS_SW-Generalcommunication AFaultF30008Powerunit:Sign-of-FaultF30008Powerunit:Sign-of-lifeerror...
驱动器的简单 联网和级联 (MAS 26) 控制单元 CU240E V3.1 参数 下载到 CU240S V3.0 的三种 方法 SINAMICS G120 / G120C / G120P / G120D: 当设定值为 0 时,电机不能运行在最小 频率 SINAMICS G120 (CU 2x0x): Is there a fault list that can be quickly integrated into configuration software ...
Once the cause of the fault has been eliminated (e.g. cooling has been improved), the original operating values are automatically resumed. Technical specifications The most important directives and standards are listed below. These are used as the basis for the SINAMICS S120 built-in units in ...
Dear all, I am facing problem in s120 drive with CU320. it was already commissioned running well but sometimes when 24V supply getting off after switch power CU showing F7800 fault that means power unit missing same one was already running. i was tri
SINAMICS驱动器S120报F30021的维修方案:F30021,GroundFault接地故障。这是一个常见故障,尤其是S120书本型设备。 动力回路:电网--变频器--电缆--电机,整体都是浮地的,不能与大地接通。 在TN/TT电网中,如果变频器内部、电机电缆或者电机自身对地(Ground,PE)接通,那么会产生很大漏电流,会触发F30021。一般在设备绝缘...
Designation Drive parameter Function chart 0 RTS Ready to start r899.0 2503 1 RDY Ready to operate r899.1 2503 2 IOp Drive is switched on (condition for the mode selection of the EPos) r899.2 2503 3 Fault Fault active r2139.3 2548 4 NoOff2Act OFF2 not activated (parti...
SINAMICS S120 Chassis Format Converter Units Chassis-2 Format Converter Units Cabinet Modules, Cabinet Modules-2 SINAMICS S150 Converter Cabinet Units E86060-K5521-A131-A7-7600 DC motors Sizes 160 to 630 31.5 kW to 1610 kW D 21.3 DA 12 E86060-K5312-A101-A2-7600 DC motors Engineering ...