例如,如果您希望将第一个输出数据存储到名为“output1”的变量中,可以在“Variable name pattern”文本框中输入“output1”。 6. 根据您的需求,可以选择其他可选设置,如“Save options”(保存选项)和“Limit data points to last”(限制数据点数为最后)等。 7. 完成设置后,单击“OK”按钮以关闭仿真设置对话框...
默认情况下Simulink软件使用绝对公差值中指定的配置参数“对话框中(请参阅Specifying Error Tolerances for Variable-Step Solvers)来计算输出的积分器块。如果这个值不能提供足够的误差控制,在Integrator块的Absolute tolerance对话框中,指定一个更合适的值。您指定的值是用来计算所有的块输出。 15楼2012-08-22 11:...
通常来说是通过属性Output data type去读取,模型如下图: 输出端口的数据类型属性:auto vdpmy_out1_block_path="vdp/Out1";my_out2_block_path="vdp/Out2";get_param(my_out1_block_path,"OutDataTypeStr")% ans = 'Inherit: auto'get_param(my_out2_block_path,"OutDataTypeStr")% ans = 'Inheri...
(P94 例2.10) (2) Save to workspace(保存数据到工作空间) 仿真结果的数据可以保存到MATLAB工作空间,这些 数据包括:Time(时间)、States(状态)、Output(系统输出) 和Final state(最终状态)。这些选项可在Workspace I/O页 的 Save to workspace框内的复选框内选择,右边的编 辑框内可键入相应的变量名。应该注 ...
或者大于Output maximum时就会报错来提醒用户。 Output data type对输出数据的类型提供了一些选项。 5.示波器模块 Scope模块是示波器模块,能够显示实数信号线。 (1) 修改Scope的输入端口个数 双击示波器模块,点击File->-Number of input ports,修改输入端口的个数为3。
2、to file模块 将模块输出到文件3、to workspace模块 该模块将数据输出到工作空间。双击该模块弹出参数设置对话框,如图所示。可以在variable name中修改工作空间的变量名;还可以在save format里修改数据存储格式(通常选array)。数据观测模块模块库包括:4、scope模块以simulink仿真时间为横坐标,以示波器输入端口数据绘制...
"Simulink cannot propagate the variable-size mode from the output port 1 of 'untitled/MATLAB Function' to the input port 1 of 'untitled/Integrator'. This input port expects a fixed-size mode. The variable-size mode originates from 'untitled/MATLAB Function'. Examine the configurations of 'unt...
To run FMU with FMU Compliance Checker, open the Command Prompt and go to the location where FMU Compliance Checker is installed. Set Environment Variable with the command illustrated in the previous section. Run FMU with the following command and observe output in terminal. % on windows FMUChec...
Disabled expensive diagnostics that check for solver data inconsistency, division by singular matrix, Inf or NaN block output, simulation range checking, and array bounds exceeded Replaced Interpreted MATLAB Function blocks with MATLAB functions (This change has the greatest single effect.) ...
一般存往工作空间的变量包括输出时间向量(Time)、状态向量(States)和输出变量(Output)。 Final state用来定义将系统稳态值存往工作空间所使用的变量名。 3)Save option:用来设置存往工作空间的有关选项。Limit rows to last用来设定SIMULINK仿真结果最终可存往MATLAB工作空间的变量的规模,对于向量而言即其维数,对于矩阵...