Simulink Code Inspector automatically compares generated code with its source model to satisfy code-review objectives in DO-178 and other high-integrity standards. The code inspector systematically examines blocks, state diagrams, parameters, and settings in a model to determine whether they are function...
MathWorks 在2011b版 (R2011b) MATLAB 和 Simulink 产品系列中新引入了 Simulink Code Inspector,该产品促进了对基于 Simulink 模型生成的源代码的检查。航空工程师们现在可以使用 Simulink Code Inspector 来创建详细的模型到代码和代码到模型的检查报告,帮助实现了 DO-178B 表 A-5 中规定的源代码验证和可追踪...
InspectorSimulinkCode认证模型生成源代码工程师检查日前.MathWorks在201lb版(R201lb)MATLAB和Simulink产品系列中新引入了Simulink Code Inspector,该产品促进了对基于Simulink模型生成的源代码的检查。航空工程师们现在可以使用Simulink Code Inspector来创建详细的模型到代码和代码到模型的检查报告电信科学...
SimulinkCodeInspectorProductDescription...1-2 KeyFeatures...1-2 WhyUseThisProduct?...1-3 CodeInspectionLimitations...1-4 ApproachtoCodeInspection...1-7 SimulinkCodeInspectorandDO-178Workflows...1-7 End-to-EndGeneralWorkflow...1-8 InspectGeneratedCodeforaSampleModel...
The Record block shows the results of this simulation. Limitations You cannot use Simulink based states with: Simulink Code Inspector Super step transitions Simulink based states do not support debugging.
Simulink Code Inspector - Code Inspector のコンテキストタブを使用して、互換性のチェック、コードの検査、および結果の表示をモデル内で直接実行 Simulink Control Design - モデル規範形適応コントローラーの設計 Symbolic Math Toolbox - MATLAB ライブエディターで次の手順を提案するシンボリッ...
slci.ConfigurationCreatecodeinspectionobject slciadvisorOpen®CodeInspector™ Advisor 1-4 2 ClassReference 2ClassReference CodeInspection slci.ConfigurationControlcodeinspectionand compatibilitycheckingformodel 2-2 3 Functions—Alphabetical List slci.Configuration.checkCompatibility PurposeCheckmodelcompatibilitywith...
Determine by Code Generation system target file由代码生成系统目标文件确定 解算器必须采用固定点类型,没有连续状态时可选discrete,步长默认为auto,在简单通用嵌入式代码生成过程中此参数没有实际作用。 optimization 优化 Unapplied change未应用的更改 Optimize using the specifiedminimum and maximum valuesFor exampleus...
Alt + Enter:为选定模块设置主要参数 Ctrl + Shift + I:打开或隐藏 Property Inspector Shift + 拖动句柄:调整模块大小,保持相同的高宽比 Ctrl + 拖动句柄:从中心调整模块大小 Ctrl + R:顺时针旋转模块 顺时针旋转90° Ctrl + Shift + R:逆时针旋转模块 Ctrl + I:翻转模块 Ctrl + F:查找模块 Ctrl + ...
§Simulink Code Inspector:提供对Stateflow 对象以及经典动作语言的支持 上市时间 R2013b 已经上市。 更多信息,请访问: 官方网站:http://www.mathworks.com/products/new_products/latest_features.html 关注MathWorks官方中文微博www.weibo.com/mathworks