ON-Delay Timer You can use theON-Delay Timer (TON) instructionto delay the setting of the Q output by the programmed time PT. The instruction is started when the result of the logic operation (RLO) at inputINchanges from “0” to “1” (positive signal edge). The programmed timePTbegin...
The Siemens S7 PLCs have five different timers in the regular instruction set yet it is missing a standard retentive on-delay timer. There is one called a Retentive On-Delay S5 Timer (S_ODTS) and its coil counterpart (SS) which provide a function to continue timing even when the timer ...
3.2.5 接通延时定时器 ON-Delay Timer 接通延时定时器时序如下: 例3.2.3 STL语句表如下: A I 0.0 L S5T#2s \\装入定时时间到ACCU1 SD T5 \\启动延时接通定时器T5 A I 0.1 R T 5 \\定时器T5复位 A T 5 = Q 4.0 FBD 功能图如下: 时序图如下: 重点之重点 结合习题讲深讲透 教案 教学内容 备注...
延迟预警 “延迟”(Delay) 参数(默认值:0.5 s)决定 SIMOCODE pro 执行所需响应之前必须一直超出 预警级别 (1.15 x I ) 的时间长度。如果未进行此项设置,则不会有任何响应。如果发生断相 s 或不平衡 50% ,则会较早达到预警级别,约为 0.85 x I 。 s 复位 如果将“复位”参数设置为“自动”,以下情况下...
Timer block PULSE GENERATOR 283 4 Function diagram 7232 - Timer blocks SWITCH-ON DELAY 284 5 Function diagram 7233 - Timer blocks SWITCH-OFF DELAY 285 6 Function diagram 7240 - Memory block RS lip-lop 286 7 Function diagram 7250 - Switch block NUMERICAL SWITCHOVER 287 8 Function diagram ...
Error The specified node is not available © Siemens AG 2024 Corporate Information Imprint Terms of Use Data Privacy Cookie Policy Digital ID SiePortal T&C Version 5.20.0 Catalog: KZ, Rdbid: KZ9581 (D4S), Valid: 01.01.2025, PubId: 10806 20241125_1633|1.0.0.0 ...
定义停止延迟区是在零件程序中通过预定义程序DELAYFSTON和DELAYFSTOF(参见“编程(页92)”)定义的。停止事件会引发停止的事件一览:事件响应Chan.basic.out.reset(复位)或ModeGroup.basic.out.reset立即(BAG复位)NC程序:M30报警16954用于启动ASUB的用户中断:延迟...
● Number of delay alarm OBs 20 20 20 20 20 ● Number of cyclic interrupt OBs 20; With minimum OB 3x cycle of 250 µs 20; With minimum OB 3x cycle of 250 µs 20; with minimum OB 3x cycle of 100 µs 20; With minimum OB 3x cycle of 250 µs 20; with minimum...
, RDF530… Overview / 概览 1) Timer with delay Off / 延时计时器 If P28=0 (factory setting), press for more than 3 seconds to set the on-time duration each time. If P28=1, 2, 3 up to 23 hours, preset with a fixed on-time, countdown begins once the thermostat is ON (refer ...
(ms) Maximum Call Party Delay (ms) Dial Digit on Time (ms) Dial Inter-Digit Time (ms) Dial Pause Time (ms) Turn MWI On FAC Turn MWI Off FAC Outbound Call Connect Timeout (ms) Wait for Ringback/Connect on Blind Transfer Hunt Group Extension Disconnect on Fax Clear...