26. show mac address-table show mac address-table命令用于显示设备的MAC地址表。这个命令可以帮助你了解设备的MAC地址表信息。 Router# show mac address-table 返回示例: Mac Address Table --- Vlan Mac Address Type Ports --- --- --- --- 1 0000.0c07.ac01 DYNAMIC Fa0/1 10 0000.0c07.ac02 DY...
26. show mac address-table show mac address-table命令用于显示设备的MAC地址表。这个命令可以帮助你了解设备的MAC地址表信息。 Router# show mac address-table 返回示例: Mac Address Table --- Vlan Mac Address Type Ports --- --- --- --- 1 0000.0c07.ac01 DYNAMIC Fa0/1 10 0000.0c07.ac02 DY...
show mac-address-table显示该交换机动态创建的过滤表 show protocols显示在每个接口上配置的被动路由协议和网络地址 show run showrunning-config命令的缩写;显示当前在该路由器上运行的配置 show sessions显示通过Telent到远程设备的连接 show start命令show startup-config的快捷方式。显示保存在NVRAM中的备份配置 show ...
MORE READING:How to Find a Device MAC Address on a Cisco Switch (show mac address-table) reliability 255/255:If you have reliability 255/255 it means that there are no input and output errors on the interface. If you have interface errors the reliability factor will decrease. ...
MAC 地址条目的有效期为 5 分钟。 Examples 以下是 show switch mac-address-table 命令的输出示例。 > show switch mac-address-table Legend: Age - entry expiration time in seconds Mac Address | VLAN | Type | Age | Port --- 000e.0c4e.2aa4 | 0001 | dynamic | 287 ...
show ipx traffic 显示Cisco路由器的SAP表 show ipx traffic 显示Cisco路由器上发送和接收的RIP和SAP信息 show isdn active 显示呼叫的号码和呼叫是否在进行中 show isdn status 显示SPID是否有效、是否己连接以及和提供商交换机的通信情况 show mac-address-table 显示该交换机动态创建的过滤表 ...
port Port (in slot#/port# format) on your Server Switch to which the host connects. physical-address MAC address of the host. net-address IP address of the host. type Type of route between the host and your Server Switch, either static or dynamic. Examples The following example...
I have a Cisco 6513 Switch with SUP 720-3B.Recently i have upgraded the IOS from 122-18.SXF8.bin to 122-33.SXI3.bin.After upgrading the IOS to 122-33.SXI3.bin iam not able to find the output of the below command example. If i give show mac-address address and enter ( mac-add...
show mac-address-table 显示该交换机动态创建的过滤表 show protocols 显示在每个接口上配置的被动路由协议和网络地址 show run showrunning-config 命令的缩写;显示当前在该路由器上运行的配置 show sessions 显示通过Telent到远程设备的连接 show start 命令show startup-config的快捷方式。显示保存在NVRAM中的备份配置...
showipxtraffic显示Cisco路由器上发送和接收的RIP和SAP信息 showisdnactive显示呼叫的号码和呼叫是否在进行中 showisdnstatus显示SPID是否有效、是否己连接以及和提供商交换机的通信情况 showmac-address-table显示该交换机动态创建的过滤表 showprotocols显示在每个接口上配置的被动路由协议和网络地址 showrunshowrunning-...