show threat-detection rate [ min-display-rate events_per_second] [ acl-drop | bad-packet-drop | conn-limit-drop | dos-drop | fw-drop | icmp-drop | inspect-drop | interface-drop | scanning-threat | syn-attack] Syntax Description acl-drop (可选)显示由于访问列表拒...
以下示例显示了对象计数,以便您了解对象组的数量、组中包含的对象数量以及 ACL、NAT 等中使用的对象数量。此信息与对象组搜索功能的性能相关。 > show object-group count Object Group Name Group Count Dyn Count V4 CNT V6 CNT ACL CNT NAT CNT OG in OG network i28Z-route 68 0 ...
If you mean ACL which should specify interesting traffic - Mikrotik has mirrored policy (like cisco ACL): [admin@Brest-R] > ip ipsec policy printFlags: T - template, X - disabled, D - dynamic, I - inactive, * - default 0 TX* group=group1 src-address=::/0 dst-address=::/0 ...
hits=463202, user_data=0x9, cs_id=0x0, use_real_addr, flags=0x1000, protocol=0 src ip/id=0.0.0.0, mask=0.0.0.0, port=0 dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0 input_ifc=WAN, output_ifc=any Result:input-interface: WANinput-status: upinput-line-status: up...
44、tion register is 0x2102xigang4506# show platform cpu pa stPackets Dropped In Hardware By CPU Subport (txQueueNotAvail)一般4500些列CPU高,在cisco文档中都有典型的描述,排障方法一般现就是三条命令,判断是STP问题,还是ACL问题,还是ACL LOG(keyword),还是广播/ARP问题,基本有个定论;更加可以使用CPU SPA...
The log Keyword in ACL 这些都可以显示特征是Cat4k Mgmt LoPri . 以host learning为例: Step 1: Check for the Cisco IOS process with the show processes cpu command. Issue the show processes cpu command in order to check which Cisco IOS process consumes the CPU. In this command output, notice...
通过交换机showproccpu的命令输出的信息可以看到.pdf,通过交换机 show proc cpu 的命令输出的信息可以看到: 在5 秒、1 分钟、5 分钟内 Cat4k Mgmt LoPri 进程的CPU 占用率分别为 91.69% 92.18% 92.23% 显然是这个进程消耗了大量的CPU 运行资源,从而导致交换机没有新的资源
ACL Helper通过show platform health 命令进一步更为详细的检查Catalyst 4506交换机的进程我们发现K2CpuMan Review进程有异常, 如下:show pla heaKxAclPathMan reprogr 1.00 0.00 2 1100500 0 0 00:00TagMan-RecreateMtegR 1.00 0.00 10 5100500 0 0 00:00K2CpuMan Review 30.0069.84 30 26100500112 106 781248:...
Armis 还在报告中提供了这些漏洞的缓解措施:1、阻止在 Translogic PTS 站上使用 Telnet(端口 23);2、部署访问控制列表 (ACL),其中 Translogic PTS 组件只允许与 Translogic 中央服务器 (SCC) 通信;3、 利用 Snort IDS 规则检测。 来源: https://www.armis.com/research/pwnedpiper...
命令 说明 show cluster 显示整个集群的聚合数据。 cluster exec show rule hits 要从集群的所有节点以聚合格式显示访问控制策略和预过滤器策略的所有评估规则的命中信息,请使用 show cluster rule hits 命令。 show cluster rulehits [ raw Syntax Description raw (可选)以 . 格式显示...